(800) 853-2651
SHOP NOW

Recent content by Iceman214406

Yesterday's Tractor Forums
  1. I

    Ford 172ci Diesel Sleeves?

    Hi all, A friend of mine is working on a Ford 4000 backhoe, and he brought the engine to my shop so we could clean it up and get everything all squared away. We found water in the cylinders and, of course, rust, so when looking online, we can get a sleeve and piston kit for this guy. This is my...
  2. I

    Vickers Vane Pump

    Hi all - can I get help identifying a model number or model series on this pump? I am trying to see if there is a rebuild kit/gasket kit for this pump because she leaks like a stuck pig! I looked all over, and cannot find anything stamped that resembles a model number :/. Any help would be...
  3. I

    Loader bucket hydraulics

  4. I

    Loader bucket hydraulics

    Hey all - my buddy has a Ferguson TO20 with a loader on the front (unmarked but looks like it may be a Wagner). He wants to install a shorter hydraulic cylinder on the bucket so it curls back more. I want to be able to help him with this but hydraulics is not my area of expertise. Is this an...
  5. I

    Ford 850 Fuel Question

    I plan on doing a tank liner so that should seal up any leaks I may have *fingers crossed*
  6. I

    Ford 850 Fuel Question

    Thanks guys!
  7. I

    Ford 850 Fuel Question

    That is what I saw as well in the manual... I know the manual is for both the 600 and the 800 so I didn't know if there was a difference for sediment bowl mount between the two different engines. It looks like whoever had this last, put the sediment bowl on backwards and has the steel line going...
  8. I

    Ford 850 Fuel Question

    Hello all, I am a little confused on how the fuel system is flowing on my 850. I see a steel fuel line running from the shut-off, down by the muffler, then goes to a rubber hose and into the sediment bowl. I am seeing images online where the sediment bowl inlet faces the engine block and the...
  9. I

    Wagner Loader On Ford 850 Question

    Thank you very much
  10. I

    Wagner Loader On Ford 850 Question

    Hello all, I recently acquired a Ford 850 with a Wagner WF3 loader. No major issues but the hydraulic lines are majorly cracked so I wanted to replace them preventatively. I am unsure as to what is the best way to relieve the hydraulic pressure so I can safely disconnect everything. Any advice...
  11. I

    MH I-162 Needs Rear Tires

    Thank you sir. Any ideas on retailers?
  12. I

    MH I-162 Needs Rear Tires

    So I walked out to Bessy this morning and her right rear was completely flat and the checking blew out so the tire is destroyed at this point (I believe these are probably the originals from 1953). Either way, the size that I see on the tires are 12.00 x 28. I have read some articles stating...
  13. I

    Magneto Question

    So my wife went out with me tonight so I could ponder this mag issue a little more... She says to me in the most serious tone - "It looks like a DeWalt battery; just replace it with that!" I laughed so hard. Gotta give her credit though - she knows what DeWalt is :)
  14. I

    Magneto Question

    Here is the other side
  15. I

    Magneto Question

    Attached is photo one. I will attached one more photo of the otherside. The information on the tag reads: Fairbanks-Morse Made in U.S.A. GW 20 FM X4B5A Serial 4471291
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top