(800) 853-2651
SHOP NOW

Recent content by Irvb

Yesterday's Tractor Forums
  1. I

    generator pulleys

    Has any one out there found a good source to find replacement pulleys on the 1950 and 1960 tractors.
  2. I

    Cockshutt 35 Deluxe

    Now this is just my opinion from years of playing with the 35's. The Hercules engines of that era were very susceptible to cracking if operator maintenance was not kept up. All that I have seen fall in that 300 to 310 serial number range but any with a prefix like you indicated were used in...
  3. I

    Cockshutt front hubs

    Ok, as I said earlier they are different. I had do do a little research before I got back to you to make sure my information was correct. The heavy standard wide spindle in side hub bearing shoulder is thicker and the bearing slightly larger. The out side hub bearing is the same on all hubs. If...
  4. I

    Cockshutt front hubs

    it probably has the cast hubs that use the 5 tab rim. if so any of the 6 bolt hubs from the cockshutts will work. Other brands may work but you may have to play with the bearing and cup to find the right combination. As for the rims you will just have to test fit or measure and look for one...
  5. I

    Cockshutt front hubs

    What kind of front end. Most any of the hubs are interchangeable except for the heavy standard wide. Irv
  6. I

    Proper spark plug for a golden arrow

    correction Golden Arrow not the Golden Eagle. Irv
  7. I

    Proper spark plug for a golden arrow

    All the Hercules used the same Champion J-6 gaped at 0.025.. models 35,Golden Eagle, 550 and 570.
  8. I

    Splitting stands

    A lot of time if you rock and continue to wiggle it, it does slip all the way in till just a 1/8 crack remains. Normally by the time you have the approximate 3/4 gap everything is aligned and starting together so I just put a couple bolts in it to keep it aligned. A lot of times once the two...
  9. I

    Splitting stands

    I have split quite a few Cockshutt/COOP tractors as it just seem quicker and easier if I am just working on a clutch, pressure plate and clutch release bearing. I have done it two ways with almost no issues. I usually block the front half of the tractor so it doesn't move or want to tilt...
  10. I

    loader for 1650

    ok thanks Mike.
  11. I

    loader for 1650

    I am in western Pa. Near Meadville.
  12. I

    loader for 1650

    OK thanks. I don't want a overly cumbersome thing but I want something heavy duty enough to pick things up with it and move gravel and dirt.
  13. I

    loader for 1650

    I am looking to put a loader on my 1650. Does anyone have a preferred model they have had good luck with? And does anyone have one for sale?
  14. I

    Oliver 1650 pto

    I am in need of a good used pto spider for a 1650. New project for me trying to repair someones mistakes. Thanks
  15. I

    1650 air intake

    thanks for the help. I can see exactly what I needed.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top