(800) 853-2651
SHOP NOW

Recent content by J R

Yesterday's Tractor Forums
  1. J

    G188D case engine

    Yes and thank you. Im turning it in the direction it runs. Im going to try changing the pump gear in the morning and try and figure out if that works. I know the books say to align the two dimples up with idler gear sheet metal point even that tube thing on TV says same thing but when you do the...
  2. J

    G188D case engine

    Jim, I turned it one revolution and the push rods are loose and flywheel DC and crank shaft pulley are on DC. The two dimples for camshaft gear are not close at all. I’ve turned it both directions off of DC and can’t see them. I’ve enclosed a picture of what pump gear is located mark now, at...
  3. J

    G188D case engine

    MEI I found the hole in flywheel housing, it had mud in it and I had to use a hammer and sharp punch to get it out. When I put the flywheel on DC it matches the crank shaft pulley on the front. NOW, I can turn number one intake push rod but not the exhaust push rod. The two dimples on cam...
  4. J

    G188D case engine

    Thank you so very much for the information. This engine has a plate on starter side and that’s where I got the numbers. I’ve looked all around for that plug and it just doesn’t seem to have one like my other 580. I will line the 2 marks up with pointer and align the pump dimple with pointer...
  5. J

    G188D case engine

    Need some help please. I have a case 580b back hoe tractor I bought without a fuel pump. Someone took it out and knew what they were doing. Number on engine is G188D. This engine doesn’t have a plug at flywheel for timing mark or DC. It is on the front crankshaft pulley. My problem is...
  6. J

    Case 580B

    Thank you "used red", Maybe I can explain a little better now, I just had surgery and now I am off those meds. Yes, I have a window on the pump and the decals say to put it at 8 degrees BFTDC. I have a 1975 case 580B. I don't have a plug in the bell housing to see any timing marks but I did...
  7. J

    Case 580B

    I have a case 580B diesel serial number 5263188 with no plug to find tdc on right side of motor I do have marks on crankshaft pulley in numbers and DC. I found 2 dimples on drive gear but none on valve gear. I have pump gear with a dimple on it. How do I install the pump gear? I have tdc and...
  8. J

    4010 clutch

    Hello. I made some big pins, 4 of them to guide both halves back together. I could roll the halves back together except ½ inch. I tried and tried then got a C clamp and with very little twisting it came together. I hooked up the lines , put 6 big bolts in, hooked wires up and started it. PTO...
  9. J

    4010 clutch

    Thank you. When I pulled the floor pan up it looks like someone had to go into it at one time. I bought this about 21 years ago and had good luck with it. My grandson helped me with haying and needles to say I had to put a clutch in it Thanks for sharing and your help. J R
  10. J

    4010 clutch

    Thank you. The shaft went back in all the way I didn’t have any problems with the two halves, I guess them within a ½ inch then used a clamp on the two halves and with very little pressure I brought them together. Tractor moves back and forth. I drove it around field yesterday in all gears...
  11. J

    4010 clutch

    Jim, I got it going good. It bolted up great. PTO and drive clutches Jim, got it going good today. Bolted right up PTO and drive clutch work great. Tested on feed grinder, good. Drove around and pulled a wagon and it worked perfectly. Just that drive shaft sticking out was the cause of it not...
  12. J

    4010 clutch

    Yes I had both sides within ⅛ inch top and bottom. I rotated pto shaft as best I could. I hooked the starter up and turned it over by a remote switch while pushing or pulling on front. Jim I found it. Maybe two problems. One was a spline on pto clutch it looks like it wasn’t finished? I...
  13. J

    4010 clutch

    Jim, thanks for your information but. I got it all together and lack about an inch and a quarter for the two halves being together. So I took clutch off now for the fourth time and put new and old on welding table. I have a difference of an inch and ⅜ measuring in center from old to new clutch...
  14. J

    4010 clutch

    Thank you Jim, We had to drive into Pueblo yesterday and I stopped by 4 Rivers, the JD house and they sent me a picture from the manual this morning of it. Not too good of one but the flat side is facing the pot clutch. I tried and tried and could get it whithin 2.5 inches of the rear and had...
  15. J

    4010 clutch

    Hello, not new to work but I took or replaced my clutch on my 4010. My question is, does the cone on the drive clutch go towards the flywheel or the transmission? When taking old one out it fell onto the shop floor. I think the drive clutch cone goes towards the rear but not 100 percent sure...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top