(800) 853-2651
SHOP NOW

Recent content by JACK V

Yesterday's Tractor Forums
  1. J

    Cranksahft pulley bolt

    I plan on intsalling a loader pump on my 2N. What size bolt do I need to replace the one on the crankshalft pulley. The one that is also used for the crank handel. Is their anything special about this bolt. Any help would be greatly appreciated.
  2. J

    Installing sleeves in a M Crawler

    I would greatly appreciate it if someone could give me some Pointers on installing sleeves In my 1938 M crawler. Do I need any type of sealer around the two O-rings? And if so what type ? Also do I install them flush with the block or let them prtrude slightly ? Take care and Have a Great Weekend
  3. J

    clutch brake

    Appreciate the heads up. the one I have is a little tight so i have to put a puller on it ? Take care
  4. J

    HARD STARTING / 2N FORD CONVERTED TO 12 VOLTS

    DANNY: BEFORE YOU GO RUNNING OFF AT THE MOUTH YOU MIGHT BE DEALING WITH A PERSON THAT HAS A VISION PROBLEM, ALL OF US AREN'T AS PEFECT AS YOU AND AS COMPUTER LITERATE. FACT IS DANNY IF I WHERE STANDING IN FRONT OF YOU YOUR ATTITUDE WOULD BE DIFFERANT. TAKE CARE AND HAVE A GREAT NIGHT
  5. J

    1938 M CRAWLER MOTOR

    HOW CLOSE ARE YOU TO MINNESOTA ?// IF THE DISTANCE ISN'T TO GREAT I WOULD TO TALK WITH YOU ABOUT PULLING THE SLEEVES AND INSTALLING THE O-RINGS. TAKE CARE AND HAVE A GREAT DAY
  6. J

    1938 M CRAWLER MOTOR

    APPRECIATE GETTING BACK WITH ME. WHERE YOU LOCATED AT ????? TAKE CARE
  7. J

    1938 M CRAWLER MOTOR

    APPRECIATE YOU GETTING BACK WITH ME. DO YOU KNOW OF ANYONE WHO COULD PRESS THESE OUT FOR ME THAT HAS WORKED ON M MOTORS AND AROUND THESE CRACKS? ONLY HAVE ONE BETWEEN 3 AND 4 CYLINDERS. TAKE CARE
  8. J

    1938 M CRAWLER MOTOR

    APPRECIATE YOU GETTING BACK WITH ME. DO YOU KNOW OF ANYONE WHO COULD PRESS THESE OUT FOR ME THAT HAS WORKED ON M MOTORS AND AROUND THESE CRACKS? ONLY HAVE ONE BETWEEN 3 AND 4 CYLINDERS. TAKE CARE
  9. J

    1938 M CRAWLER MOTOR

    APPRECIATE THE HEADS UP. WHERE CAN I GET O-RINGS? AND WHEN I PULL THE SLEEVES DO I HAVE TO BE CONCERNED ABOUT THE CRACK BETWEEN THE SLEEVES ? ANY ADVICE TO GET THEM OUT. TAKE CARE AND HAVE A NICE SPRING DAY
  10. J

    1938 M CRAWLER MOTOR

    I HAVE A 1938 M CRAWLER THAT I'M REBUILDING THE QUESTION I HAVE IS THE MOTOR. AFTER CLEANING THE BLOCK I FOUND A CRACK BETWEEN THE NUMBER THREE AND FOUR CYLINDERS. HEAD GASKET COVERS IT GOOD. IS THIS SOMETHING I SHOULD BE CONCERNED ABOUT AND IF SO WHAT IS A GOOD FIX. ALSO NEED SOME IDEAS ON...
  11. J

    installing dearborn loader on a 2N

    I need information or a manual on how to install a dearborn loader on my 2N. Everything including installing the front axel pivot. could you send the information to my e-mail address [email protected] thanks
  12. J

    REMOVE HG CRAWLER MOTOR

    HOW DO I REMOVE THE MOTOR FROM AN OLIVER HG CRAWLER ??? THE FRONT NO PROBLEM. THE BACK BELL HOUSING ETC
  13. J

    OLIVER HG

    TAKING THE MOTOR OUT OF MY HG / OC3 HOW DO I REMOVE IT FRONT NO PROBLEM CAN'T FIGURE OUT THE BACK HALF. WHAT BOLTS SUPPORT THE BACK AND WHERE ARE THEY LOCATED ?????
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top