(800) 853-2651
SHOP NOW

Recent content by Jacobsen1450

Yesterday's Tractor Forums
  1. J

    2444 with loader (stuck clutch)

    Just got the tractor running after sitting for a long long time. and the clutch is very stuck. How should I go about doing this? I have another tractor capable of towing the 2444, should I just tow it around in 4th gear until it pops loose? I have never dealt with this issue before so any...
  2. J

    2444 with loader (headlight question)

    haha! thank you, this tractor should be all set once I install the new fuel pump
  3. J

    2444 with loader (headlight question)

    Thank you for the response,but i do not see a link
  4. J

    2444 with loader (headlight question)

    I am fixing a 2444 for someone and noticed that on front of tractor where there would normally be headlights. there are just 2 chrome/mirror flat disks. Is this original?
  5. J

    8N cylinder deactivation idea?

    Hello! I recently fouled out a spark plug from someone leaving choke closed while operating tractor. In process of finding while plug was fouled I unplugged each wire one by one until I got the tractor running on only 1 cylinder. It starts and idles like a charm and I?m wondering if I could set...
  6. J

    3 point acting weird

    Where would that be located? Can I access from pulling the top cover off, or do I need to split tractor...........again :(
  7. J

    3 point acting weird

    I have a 1950 8N. This winter I used it for plowing and it worked like a charm. Until one day I went to clear my driveway and the back blade didn?t want to touch the ground. It would raise up like normal and when I drop it down it would stop .5 inch above ground. When I flip lever under seat...
  8. J

    Jacobsen 1450 super Cheif

    I just finished rebuilding my Kohler engine and put it back in tractor. The tractor start and runs great and headlights work as well. However it does not seem to be charging the battery. It has the original voltage regulator and I?m wondering if I have the wires mixed up. It has 3 t connectors...
  9. J

    Identify this back blade

    Looks very similar to a king cutter RB-72, but the angle selection plate is round on mine. The king cutter has the sides of circle cut
  10. J

    Identify this back blade

    ok i give up just email me at [email protected] and ill send them to you. Then mabye you could post them for me
  11. J

    Identify this back blade

    ok i think they should show up now
  12. J

    Identify this back blade

    ok here are the photos
  13. J

    Identify this back blade

    Can anyone tell me how to add pictures?
  14. J

    Identify this back blade

    I?ve had this thing for a while now and I got it from my grandfather. Can anyone tell me what brand it is?
  15. J

    Axle Worries Revised

    My 8N has sorta the same issue. My axles are fairly new but the hub has alot more wiggle room than the one on other side. There is also a faint screeching sound on that side when im going at high speeds. I suppose the bearing could be worn but it was not doing it before I replaced seals. As...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top