(800) 853-2651
SHOP NOW

Recent content by Jake Collie

Yesterday's Tractor Forums
  1. J

    JD 440 IC generator questions

    Thank you buickanddeere. I am finding out every video you watch on the internet isn't correct.
  2. J

    John, I would really like to speak with you about my type A generator issues. If you could give...

    John, I would really like to speak with you about my type A generator issues. If you could give me a call @ 715 213-5560 when you get a chance that would be great! Thanks, Scott
  3. J

    JD 440 IC generator questions

    This might be a long post... My generator wasn't charging ( Delco type A 6 volt positive ground 1101859) so I did a few tests. I removed the belt, removed the A and F wires, jumpered A to F and put power to A. I believe this is supposed to motor the generator. The generator tried to spin, but...
  4. J

    White 2-105 3 point control

    I was moldboard plowing yesterday with the 2-105 and I found myself having to hold down on the 3 point lift hydraulic control the last few rounds to keep the plow in the ground. (Just the front of the plow - the remote worked fine for the rear plow cylinder) If I took my hand off the control...
  5. J

    2-105 transmission lube sensor

    Should be a normally closed switch with oil pressure opening up the switch.
  6. J

    2-105 transmission lube sensor

    Correct part should have 1 terminal. They told me they have the problem fixed now
  7. J

    2-105 transmission lube sensor

    UPDATE - I contacted AGCO and started asking questions. After a while, they realized they had put the wrong pressure switches in the system. The correct pressure switch is adjustable from .5 PSI to 1 PSI. It is also a normally closed switch. The AGCO part number is 30-3164047. Hopefully this can...
  8. J

    2-105 transmission lube sensor

    Has anyone changed this sensor recently? My light never comes on, so I grounded the wire attached to the sensor and then it came on. Appears the sensor is stuck. The manual shows that the sensor should close at .6 PSI. The new sensor I bought from AGCO closes at 14 PSI. I don't think the trans...
  9. J

    Bushing in MFWD axle housing. Super 99?

    To see the Chris Losey video that shows the "not factory" bushing, look at the 34:00 minute mark on his "Front Wheel Axle Assembly - Oliver 1855 Restoration Part 18" video.
  10. J

    Bushing in MFWD axle housing. Super 99?

    Here is a drawing of one of the bushings we made. It shows 5 thousandths but we ended up using 7 thousandths.
  11. J

    Bushing in MFWD axle housing. Super 99?

    You have to have a machinist measure the inside of the axle tube and the outside of the axle where the seal rides and have a bushing machined to fit. You will need to measure both left and right axle tube IDs because they are probably different. We used a nice tight press fit for the OD of the...
  12. J

    1850D Tachometer Drive

    I believe it's called the AUXILIARY DRIVE - DSL. 1850 Parts book page 16.
  13. J

    1850D Tachometer Drive

    158757AS is the shaft with core, 80 long for diesel FYI
  14. J

    1850D Tachometer Drive

    I believe the tach adaptor is what the 90* gearbox is called. At least that is what I called it when I bought my spare. The Tractor Doctor should still have my good spare and maybe they have another one as well. Look them up at tractor-dr.com. Very knowledgeable Oliver people. I got my spare...
  15. J

    1850D Tachometer Drive

    FYI - The tach adapter part number is 158761A
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top