(800) 853-2651
SHOP NOW

Recent content by James Wendling

Yesterday's Tractor Forums
  1. J

    distributor

    That sounds like a good thing to check and would be the easy way out. As far as the distributor not being all the way down,I had not touched it yet and it was tight with the two side bolts. Thank you.
  2. J

    distributor

    My Ford 600 series quit running and in checking the points I found that a point had fallen off of not an old set. This was remedied with a new set and my problem was over,so I thought.When it didn't start I discovered that the distributor shaft that the rotor sits on didn't turn a few times when...
  3. J

    tractor locking up.

    Thanks for the reply,I never heard of any thing like that.
  4. J

    tractor locking up.

    Whew!that was a close one.My Ford tractor 600 4 speed with a Howard gear to run a tiller almost let me down when we were in a very large fourth of july parade yesterday pulling a farm wagon with passengers. The first thing was that it wouldn't start during the parade.After wiggling the batt...
  5. J

    Emblem housing

    When laying each huousing down on a table,emblem side down, with bolt holes matching the measurement top to bottem on the old is 7 3/8,the new one is 8 1/8,only about 3/4 of an inch.Different than I first stated,I think maybe showcrop might be right,the old one could have been mashed down some...
  6. J

    Emblem housing

    I just bought an emblem,and housing for a Ford 600. It hasn't been installed yet because of painting. The wider part of the housing (that is the side next to the hood ) is about 1 1/2 inches wider than my old one. (that is top to bottem measurement) When I do install it I am wondering if the...
  7. J

    Paint

    All is not lost. I did some mixing--red rustoleum with just a small amount of this orange,I mixed until I got just what I was looking for.It has the right amount of red,and a red orange look. Thank's alot guy's. The grey looks perfect.
  8. J

    Paint

    Thank you guy's I will exchange this paint. Nothing against A.C's but I am painting a Ford.
  9. J

    Paint

    I bought tisco tp 310 Ford red for my 600 series,and am dissapointed.To me it is orange. I was hoping for more of a redish,orange. Was orange the right color? I don't remember it being this color. The color that I am removing is blue like so many have been painted to make them look like a later...
  10. J

    Term

    It is on the left side along with the pto lever.behind the foot. It is definitly for running my tiller as I have done it for years although that has come to an end,the tiller will be run by unother tractor. The 600 will no longer be a working tractor,it will be for parades,and to keep nice...
  11. J

    Term

    My deep reduction gear on my 600 series for running things like a tiller has been called a Sherman gear by some,and that to my understanding is for a higher speed. At the same time,I have heard it called a Howard gear which I also believe should be proper. If Howard is correct was it made by the...
  12. J

    paint

    Wow,that is my answer,I will paint some of the bolt on's black. I will also except the good looking one that the Shriners rejected.
  13. J

    paint

    On my 600 restoration I will of course do the correct red,and grey.It is now grey,and blue,yep so many have done this to keep up with the newer models ,but in restoration the original color just really makes an eye catcher. The question is should the generator,and starter be black to bring it...
  14. J

    600 Fenders

    Thanks a lot guy's I will try my angle grinder.
  15. J

    600 Fenders

    My first thought was that they are guides,but they are much too solid I think.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top