(800) 853-2651
SHOP NOW

Recent content by James3504

Yesterday's Tractor Forums
  1. J

    450 Engine Compression???

    Thanks for the responses. My numbers were all relatively close but not that high. It could of been my ole tester or just operator error. Well I guess I'll split the tractor throw in a rear main seal and stick it back together. Also does anyone know how tight the bolts should be on the rear seal...
  2. J

    450 Engine Compression???

    Thanks for the earlier comments. My question still didn't get answered. I was wanting to know how many pds. should each cylinder have? Since I've got to split the tractor to fix the rear main, I was rolling around the idea that I might put an engine kit in while it's all apart again and cold...
  3. J

    450 Engine Compression???

    My 450 has developed an oil leak very rapidly from the rear main. I was wondering if anyone knows how many pounds the compression should test at. I was trying to eliminate potential factors that could be causing it to start leaking so much all the sudden. Could it of broke a ring possibly ?? I'm...
  4. J

    Trouble 450 clutch

    Clutch disc will only fit one way. If it's put in backwards it hits the center before friction surfaces meet.
  5. J

    Trouble 450 clutch

    Nothing is jambed it all slides freely on the shaft, engages the fingers correctly. I just don't know. This isn't my first clutch job, I'm just puzzled.
  6. J

    Trouble 450 clutch

    Clutch Had a tollerance around the flywheel. Fingers are connecting to the p.plate and moving the fingers in when pedal is pushed down. I can see this through the inspection plate hole. New pilot bearing spun freely, installed correctly. Clutch will only fit one way because if its turned wrong...
  7. J

    Trouble 450 clutch

    Got the tractor all back together. Trans shifts well w/ engine not running. I adjusted the clutch and ta by the book. 1" freeplay on clutch, when ya start tractor in neutral, clutch is disengaged as it should be, but when you try to shift into first it just grinds. I then adjusted it to the end...
  8. J

    450 Clutch

    Thanks guys,I'll stick it all together and finish up. Thanks for the input.
  9. J

    450 Clutch

    I'm currently rebuilding the ta, clutch and everything in between. When I got to the main trans. clutch I replaced it with a 6 button hd and new presure plate. When I went to remove the three spring compression bolts in the new pressure plate, the fingers didn't release very much at all. I was...
  10. J

    450 hyd.

    Guys I had the same problem. Tried everything I could think of, for months. My experince came from changing the fluid and cleaning the filter. Nothing happened, I tried all the tricks yuns mentioned and nothing worked. Checked all lines and figured out that no oil was coming from the pump. So I...
  11. J

    MW Parts

    I hear some guys talking about M&W stuff. I assume this is an aftermarket company. Are they still in business or operation, if so, where are they located? I'm interested in purchasing a power governor for my 450. Any help or information would be helpful. If someone has a used one in terrific...
  12. J

    No fifth gear

    I've have the same problem too Steve. Except the H's I have are earlier model's, can't remember if it is the 40 or 41 but one of mine will not shift fifth gear. Someone mentioned something about a lockout bolt, what is that and where is it located. That may be my whole problem. I just don't know...
  13. J

    TA problems help

    The ta clutch or the ramp gears and bearings or all of it?
  14. J

    TA problems help

    I recently bought a 450. When you pull the TA, it works briefly and then you hear a spinning noise. Is it busted, worn out or out of adjustment. I'm new to TA's and know nothing about them. Any help would be great. I don't know how to adjust or determine what's wrong. Maybe some of you guy's...
  15. J

    Pullin parts and assesories

    I'm having trouble finding websites or places that sell drawbar/weight bracket- wheelie bar set-ups. If it makes a difference I have a farmall 450. Thanks for any help or suggestions.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top