(800) 853-2651
SHOP NOW

Recent content by Jason Drabek

Yesterday's Tractor Forums
  1. A

    More Visiting...LAI Case Shopping

    As long as I'm throwing out the questions....Do any of you know of a nice LAI for sale in or near Wisconsin? It would be fun having one to go along with my VAC, SC, and DC. LAI would have to be pto equipped. Thanks, Glenn
  2. B

    SC Ignition Switch

    With the push/pull Ignition Switch pulled out shouldn't I have voltage at the coil? Thanks
  3. T

    200 Two Row Cultivator

    I have a 200 Series John Deere two row cultivator that I am trying to restore to fit a late B John Deere tractor. I have a few parts missing like a rock shaft lift link, front of tractor top bracket for cultivator, and a lower plate on front of tractor. I have been told this is a quick attach...
  4. 4

    41 Mcormick deering 41

    We got it bought, now to move it
  5. H

    Help me identify this corn chopper!

    Can anyone identify the make of this corn grinder and tell me what the original color is supposed to be?
  6. T

    hello, adding a rear hyd remote on dc

    any good ideas or photos of adding a rear remote to my case dc , 1950 model. thanks, Jim
  7. J

    d 17 crank

    Does any know if I can put a ac d 17 crank and rods in a coop e3 without to much machine work
  8. J

    Brakes for Model 30 Co-op

    If you can still see the number on the seal you can have it crossed. Picked up front wheel bearings and grease seals from an allis dealer.Heard that john Deere has numbers that will cross rear oil seals. Car quest is pretty good to about crossing numbers.
  9. J

    Coop rear end has a goofy shaft

    where can I start looking for that kind of information? Who are the others? the axle is the the same per the wrong styled hub
  10. J

    Coop rear end has a goofy shaft

    I have a coop e3 with 2 different rear axles. I know that the splined axle is correct, but can anyone tell me off of what tractor that a keyed shaft would have come out of to fit the housing of did someone just rig it to work. The number on the hub is 3870Q63 and the key is 5/8 inch. Im just...
  11. J

    Coop rear end has a goofy shaft

    I have a coop e3 with 2 different rear axles. I know that the splined axle is correct, but can anyone tell me off of what tractor that a keyed shaft would have come out of to fit the housing of did someone just rig it to work. The number on the hub is 3870Q63 and the key is 5/8 inch. Im just...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top