(800) 853-2651
SHOP NOW

Recent content by jeff24

Yesterday's Tractor Forums
  1. J

    2020 rockshaft cover gasket

    thanks Is there a recess this is suppose to set in? I do not remember seeing any when i had it off?
  2. J

    2020 rockshaft cover gasket

    i have a john deere 2020 that i replaced the rock shaft cover gasket because it was blowing hydraulic oil out on the right hand side about in the middle. After a few hour of running the same thing happened again. Any ideas of why?
  3. J

    4430 coolant heater

    I have what i think is RE29408 block heater. i have removed the large nut but that goes around the heater element but i am not for sure what to do next to remove.
  4. J

    2020 brakes/ transmisson

    i would lie to say thanks to all your help. After pulling both sides and inspecting the brakes i put it back togther and it coast as it should. The only thing that i did was cleaned the brake ring piston. There was about 2 teaspoon of gray crap behing them. i was suprised when it worked...
  5. J

    2020 BRAKES OR TRANSMISSION

    I recently just bought this tractor knowing that it had this problem, I know very little about the maintenance except that I know the previous owner and he takes excellent care of all of his equipment. He has owned this tractor for approx. 30 years. I believe that he uses all shell products in...
  6. J

    2020 BRAKES OR TRANSMISSION

    I am not for sure if I tried coasting with putting it in neutral, I think I just pushed the clutch in. When in road gear and going down a hill and you push the clutch you feel an immediate slow down and it will come to a stop. I also have a 1020 gas tractor that I am comparing this to. On a...
  7. J

    2020 BRAKES OR TRANSMISSION

    After unhooking the brake lines and bleeders my tractor still did not coast like it should. So i have removed the left axle housing to inspect the brakes. This side looks like new, but did not have a john deere stamped part number on it unless it was on the back in yellow in nice handwriting...
  8. J

    2020

    I took off both brake lines and one bleeder screw, one is stuck and i plan on letting it soak with penetrating oil. It still does not coast like it should. By doing this what did i elimante and what should i do next?
  9. J

    2020

    I recently purchased a john deere 2020 and it has some type of problem. When you push the cluth in it does not coast like it should. i have inspected the tranmission screen and it was clean, i looked at trans filter and it is also clean.it does not seem like it is a brake problem.Is there any...
  10. J

    1460 REEL LIFT

    After doing a little more research, i replaced the oil pressure sensor, thinking it would not fix the problem since it seemed to be working. this did fix most of my issues but a different issue resulted. When using the auto header height control when going down it jerks down not smooth? Not for...
  11. J

    1460 REEL LIFT

    I think so, but before i took apart I wanted to make for sure i was not missing something simple. I have never taken this apart. Is there anything to watch for?
  12. J

    1460 REEL LIFT

    On my 1984 1460 with electric over hydraulics my 1020 head Everything working as is should except for the reel lift. When I lift it up i hear the pump running (pressure) but it does not stop and the reel does not go back down until i do another function such as lifting the head and then it goes...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top