(800) 853-2651
SHOP NOW

Recent content by Jerry Archer

Yesterday's Tractor Forums
  1. L

    Farmall M Pops out of 4th

    I am refurbishing this tractor for a senior project in high school. It is a '41 M. When I was using before I started tearing it down I noticed it popped out of 4th occasionally. Only 4th though. I have only taken the cover off the transmission,as of yet. Before I start tearing into it I was...
  2. E

    troybilt carb

    i recentlyu bought a troybilt big red powerhorse, it has a unused brush chipper with it too, the thing has not been run in some time, and i got it running now, but... the float bowl on the carb is rusted thru, the thing was full of rust up past the float and needle and seat, so im trying to find...
  3. F

    International harvester 334

    I'm a Ford 'N' person mostly. Don't know much about them though, but even less about other tractors. Been looking for something to hang a Ditch Witch Backhoe off of. Most on the 'N' board say it's best to find something a little bigger than the 'N' to use. I was hoping to find a good runner...
  4. J

    MY HEART

    Zane: I will be praying for you. Jerry from SO CA.
  5. J

    MERRY CHRISTMAS

    Merry Christmas to all.
  6. J

    weak 8N hydraulics..Fixed!

    Mike, glad you got her fixed.(1940 9N & 1952 8N). These "N" will last forever, Take care.
  7. J

    King Kutter dirt scoop question.

    Mike. My three point system quit working,(1940 9N) & with the help of this Forum, I found the problem & fixed it. Broken relief valve. Good Luck, "N"'s will last forever.
  8. J

    Bruce/re:50th

    Bruce, I remembered the butt cans, but no ice at the bottom. God Bless (1952 8N & 1940 9N)
  9. J

    Bruce/re:50th

    I was housed in wooden barracks, got cold in winter times.
  10. J

    Bruce/re:50th

    Hello Bruce, have 8N (1952) & 9N (1940), both restored, org colors. This Forum has helped me a lot in the past. When I saw Ft.Bragg, it brought back a lot of memories. I was at Bragg in 1962/63, but was a Legg (Did not jump), in a Chemical Co. God bless.
  11. J

    9N Hydraulics

    Good news. Installed new valve, PTO shaft and PTO lever/inspection cover, added new hydraulic fluid. Started 9N up and now 3 point system works great. Thanks to all for your help, these N's will last forever. Great Forum.
  12. J

    9N Hydraulics

    Zane, I got the valve out. Took off the PTO cover on left side,and valve broke free. I am going to try & send a picture of the old valve. If you do not get the picture, I found the plunger inside of the spring was broken into. I hope this was my problem. Have you ever seen this problem...
  13. J

    9N Hydraulics

    Zane: All I have for now is an 11/16" open end wrench, I am turning it counter clockwise. It seems like it is welded in there. I can't use an 11/16" box end wrench because of the cotter key. I just tried again about 5 minutes ago & it will not come free. Before I break something, I'm going...
  14. J

    2N Hay Ride Hitch Setup

    Greg, Thanks for sharing, great pictures.
  15. J

    9N Hydraulics

    I have a 8N(1952)&9N(1940)restored,orginal colors. Thanks again to Dell, Zane and others who helped me with my problems with the 9N back in 2009. Now my problem is, I cannot get the check/safety(relief)valve out of the pump housing, on the 9N. I think it has been in there since 1940(Has cotter...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top