(800) 853-2651
SHOP NOW

Recent content by JGudde

Yesterday's Tractor Forums
  1. J

    Ford 2110 Tractor

    I have a ford 2100 tractor that I was bush hogging with and the engine looked up. Took head off to check for piston or sleeve scoring and they looked ok . Pulled pan off and found balancer was looked up damaging the balancer drive gear and idler damaged. Parts are hard to find so I am...
    • JGudde
    • Thread
    • Replies: 0
    • Forum: Ford
  2. J

    Massey 65 Gas

    Can someone tell me what the timing on a 65 gas tractor is. I have not been able to find what it should time at 5 degrees before TDC or what it should be. Thanks
  3. J

    Massey Ferguson flat rates

    I was not familiar with the hydraulic system so I spent a lot of time trying to troubleshoot the system. I do not feel like I should charge someone all my time for my inexperience with the tractor model. Would like to get some idea of how long it should have taken to do the repair. Maybe...
  4. J

    Massey Ferguson flat rates

    I thought maybe an older massey dealer would still have flat rate info from that time period.
  5. J

    Massey Ferguson flat rates

    Would anyone have a flat rate manual that would have repair flat rates for a 1100 massey. Needing the flat rates for replacing the hydraulic charge punp, the main hydraulic pump and the front axle. If someone would have this info or know where to get please let me know. Thanks
  6. J

    2590 poweshift

    Can anyone tell me which tube goes to the c-3 clutch as I have pulled the valve to check the tube and orings. Thanks
  7. J

    2590 poweshift

    What do you mean by pickup tube are you talking about the tube from the valve to the c-3 clutch or something else?
  8. J

    2590 poweshift

    I have a 2590 that will not move in 2nd and 3rd powershift. Checked some pressures and found that in 1st c1 and c2 pressures are 185 psi. in 2nd c1 and c3 pressures is 100psi. In 3rd c2 and c3 pressures are 100psi. Clutch down c4 185psi and reverse c2 and c4 pressures 185psi. Appears...
  9. J

    9700 joystick

    I am installing a loader on a Ford 9700 tractor. I want to use a joystick control valve on it. Does anyone know how to hook the joystick valve into the tractor hydraulics? My local dealer does not have anyone old enough to remember or know how to do it.
    • JGudde
    • Thread
    • Replies: 1
    • Forum: Ford
  10. J

    Farmall 350 piston

    I need info on rings for a 350 with a 374473R1 Fire Crater piston.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top