(800) 853-2651
SHOP NOW

Recent content by jim(SE-Mich)

Yesterday's Tractor Forums
  1. J

    1954 NAA Jubilee Hydralic NIGHTMARE NEED THE EXPERTS HELP

    Do you have a vane pump or a piston pump? If you don't know take a picture of the pump and post it. I have worked on my Jubilee hyd a couple of times and it was always the pump not putting out enough pressure. A little air getting to the pump will cause this problem. You should not waste...
  2. J

    I want to thank Zane for his help.

    Re: Jubilee Hydraulic problem in reply to jim(SE-Mich), 06-13-2011 20:16:43 I am very grateful for help from all who responded to my request for assistance, but I want to especialy thank Zane for his lengthy explaination of how to troubleshoot my Hydraulic problem I was having with my Jubilee...
  3. J

    Jubilee Hydraulic problem

    My jubilee lift bleeds down and continually jumps up, then bleeds down again then jumps back up so this must mean I need a new piston with an "O" Ring??????? What else could cause this problem????? I appreciate any and all advise to solve this problem. Jim
  4. A

    MF#12 Bill hook removal

    I have a MF#12 baler that needs new bill hooks. I have no service manual yet, and the closest dealer is 50+ miles away. Can they be replaced without a complete dismantal of the tieing assembly? I know there is a pin thru the center if the hook, just can"t access it.
  5. J

    adjustable tappet adjusting

    Dunk; Your attitude shows you are nothing unique. Just like everyone else. We all are quite the same with small differences that don't make much difference in anything.
  6. J

    8N hyd lift - questions with pics...

    I haven't checked my manual but I think your cam pin is worn off. I can't see it. If you don't get a picture from somewhere I could send you one. Don't know how to post them here.
  7. J

    Planing a Cylinder head

    I think I would consider adding a solid steel headgasket to the one you have to compensate for what you are losing after milling. With the low compression and lots of headbolts this should work fine. JMHO Jim
  8. J

    Value of Ford 9N Tractor

    It makes quite a difference where you live. The state and location in that state would make quite a difference especialy in a state like Michigan. Jim Tractor owner for 50 years.
  9. J

    Starting problems

    His question was how to wire his alternator. He did not ask if he should make the change. He was not asking for advise on wheather he should make the change. He did still has not got the answer he asked for. He simply wants to know if anyone can help him with the wiring of an alternator. Jim
  10. J

    Starting problems

    Why are people against upgrading to 12 volt? Because they do not realize the tremendous benefit from changing to 12 volt. Between 12 volts and electronic ignition this is the smartest improvement you can ever make to a 9N,2N,8N, or Jubilee. Why don't any automobile manufacturers in the world...
  11. J

    Jubilee Smokes

    Could it be an excessive amount of gas on first start-up? Could your gas shutoff be leaking very slow and filling up the carburetor and breather pipe and when starting drawing the excessive gass into the engine causing the smoke? Excessive gas will cause smoke. Just an idea. Be sure to give us...
  12. J

    Jubilee Smokes

    Could it be an excessive amount of gas on first start-up? Could your gas shutoff be leaking very slow and filling up the carburetor and breather pipe and when starting drawing the excessive gass into the engine causing the smoke? Excessive gas will cause smoke. Just an idea. Be sure to give us...
  13. J

    8n eating bendix gears

    My best guess (after 50 years owning and using 9,2,8N's) would be to retard the spark slightly. I am convinced that (from your description) it was kick-back from the ignition firing too soon. Did you reset the timing recently or change the points? Be sure to let us know for everyones benefit...
  14. J

    converting front mount to side mount

    Is there an internet article on this modification? I have an idea I believe would be quite easy but where did you get this info?
  15. J

    53 NAA Jubilee

    I have the lines for a vane pump. Would sell for $30 for my trouble packaging, plus shipping cost. Dark here now but could look in the A.M. to be sure they are still hanging in the barn. They were working great but I replaced the pump with a piston type and had to use different design lines. Jim
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top