(800) 853-2651
SHOP NOW

Recent content by jnharsh

Yesterday's Tractor Forums
  1. J

    1940 Case V - Brake Question

    Still working on restoring a 1940 Case V. The seal behind the brakes has failed and working on getting the linkage, plate, and brakes out to access. Got to the yoke and rod that are around a large pin that runs from the outside of the tractor to a cavity in the cast. I believe I need to...
  2. J

    1940 Case V - Pilot Bushing - Can’t find the right ID

    I need a new pilot busing for a 1940 Case V model tractor. The input shaft measures OD .63 inches. I found a part referenced for a VA that is Sintered bronze 0.625" inside diameter 0.815" outside diameter 1.000" length The length and OD work, but the ID is too tight. Been looking all...
  3. J

    1940 Case V - Clutch Quill - Transmission input shaft gasket question.

    First, thanks to everyone on this Forum who has helped me along the way. Back working on the Case and finishing up the split, new Clutch, throw out, belt pulley seal, clutch quill input shaft oil seal and some input shaft bearings. When I install the Clutch quill plate back on with the three...
  4. J

    1940 Case V battery box/hood latch?

    What does the tab attach to when it is rotated ? Does it just go under another fixed tab hanging down from the screw hole in the fuel tank cover ?
  5. J

    1940 Case V battery box/hood latch?

    Thanks. This helps a bunch.
  6. J

    1940 Case V battery box/hood latch?

    Ive been working on and off the past year or so on restoring a 1940 Case V that belong to my Grandfather. Making good progress but one of the simpler things has been hard to find a reference. The access hood to the battery box has a vent hole in the sheet metal and just in front of it a hole...
  7. J

    Massey Harris - F162A308 Tappet Lifter

    I have to travel to California for a couple days , but will dig into it when I get back Friday. Might have to end up getting the entire lifter and opening the lower end like you said. Jeff
  8. J

    Massey Harris - F162A308 Tappet Lifter

    Your seems to be different. ? Mine pictured below has coarse thread section that screws into the lifter. Then a flange and then the larger section that has very fine threads that the jam nut rises up. In my picture the jam nut is threaded all the way up to the top 9/16 inch hex head that is...
  9. J

    Massey Harris - F162A308 Tappet Lifter

    Thanks for the update. Yep, I think they might drop out the bottom with the cam out or broken , or you can lift high enough to screw the adjuster nut and jam nut out with the valve out or lifted. Jeff
  10. J

    Massey Harris - F162A308 Tappet Lifter

    You can pull off the manifold off and open the tappet cover on the side. You can hold the tappet lifter with a 7/8 wrench and use a 3/4 inch wrench on the jam nut to wind it counterclockwise wise until the entire adjustment screw and Jam nut will come out of the lifter. The screw and nut are...
  11. J

    Massey Harris - F162A308 Tappet Lifter

    That would be great , let me know. I m fixing up the tractor out at my Dads place in Southeast Iowa. If you find something I could use I can make arrangements to get it out to me. Jeff
  12. J

    Massey Harris - F162A308 Tappet Lifter

    I actually only need one. The top adjusting nut is damaged. On cylinder #1 exhaust. If I can find an exact replacement I could probably fix with just the adjusting screw and lock nut of a new lifter into this existing one. Jeff
  13. J

    Massey Harris - F162A308 Tappet Lifter

    I am restoring a Tractor that has a Continental Flathead F162 (F162A308). I need the adjusting screw 9/16 Hex head and the 3/4 Jam nut in the Tappet Lifter that has 7/8 flats on the side. Any good resource to find this part? I have looked through the parts on this site but they appear to be...
  14. J

    Aftermarket Case V Fenders?

    I'll shoot you an email., Traveling through Camdenton, MO soon.
  15. J

    Aftermarket Case V Fenders?

    Sounds good. I'm restoring the Tractor in Southeast Iowa. I'll send you an email. Thanks Jeff
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top