(800) 853-2651
SHOP NOW

Recent content by joe brabank

Yesterday's Tractor Forums
  1. J

    wd narrow front spindle shaft bearing and seals

    checked djs part ac-1793d, those bearings look to be for the wheels,the spindle shaft lower end has this odd bearing with cork seals. the upper end by the worm gear has a bushing. thanks for the help
  2. J

    wd narrow front spindle shaft bearing and seals

    the bearing cup wyatt 11480w , bearing wyatt 11480 with barrel shaped rollers, can not find these bearings or seals on this site or other sources . the spindle block assembly also will need repair. thanks for the help.
  3. J

    new valves for a 226 cid head

    purchased head rebuild kit ,the intake valves have the wire ring grooves the exhaust vales do not. how big a risk would it be not have the wire rings on the exhaust valves?
  4. J

    JD 350 crawler loader follow up.

    i found a small metal filter behind the outlet fitting
  5. J

    H3 crawler steering clutch

    bend a narrow wire hoop, lay it on the axle shaft across the retainer clip locking hole before pushing the axle into the diff. then bent wire up out of your way,install steering cluth.reach into housing with long screw driver,hook the wire sliding the axle out.when the wire is free you will be...
  6. J

    which carborator for best perfomance

    WD with 4 1/8" overbore,WD45 manifold and head. TSX159 or TSX464
  7. J

    Super C Ignition

    check drive gears between dist. and drive.the slotted pipe plug is where you add the lube,most get overlooked when servicing causing gears to rust/wear until they jump time
  8. J

    wd,missing pilot bearing

    tractor s/n wd111726,engine s/n wd320877pa. during tear down found the pilot bearing missing.after searching threw the wd/wd45 service manual under flywheel "the pilot bearing was removed w engine s/n 310920 and the shaft changed.no pilot bearing is needed."effective with wd45 engine s/n30956...
  9. J

    WD gas tank mount

    knobs for throttle and hydraulic controls are available from steiners,page 54,part #ACS184
  10. J

    which parts should i use

    making one working wd allis from 7 parts tractors. i have three styles of fan blades,4 blade,5 blade and one 6 blade. also found two types of thermostat housings/manifolds.one only takes h2o from the front of the head the other is connected to both the front and rear ports.any suggestion as to...
  11. J

    262 BUDA ENGINE rebuild

    head was removed,head gasket was blown between cy. 1&2 2%3 and 4&5. liners look lower then the deck. not worth measuring because when you scratch your finger nail across the liner the deck is higher. have done old cat engines by cutting the counter bores and shimming the liners.did not know if...
  12. J

    262 BUDA ENGINE rebuild

    would a G226 gas from a d17 fit in were the 262 diesel came out. the 262 was mounted with an adapter plate which also was used for the starter mount.
  13. J

    262 BUDA ENGINE rebuild

    any suggestions on how this tractor could be salvaged,maybe a repower? if so what would be the best match and easy to find.
  14. J

    262 BUDA ENGINE rebuild

    looks like a rebuild, but is this buda engine worth the cost? is it an unreliable engine no one wants? are all the parts available? D17 s/n2497D engine s/n 100665 all engine kits found for s/n 111??? and up...
  15. J

    ALLIS D17 WITH 262 BUDA ENGINE

    DR.ALLIS, WHAT IS THE FUNCTION OF THE AIR OR ENERGY CELLS IN THE HEAD.REMOVED HEAD TO REPLACE BLOWN HEAD GASKET,WILL REDO VALVES AND ETC.WHILE HEAD IS OFF.ANY INPUT YOU GIVE ABOUT ENERGY CELLS,HEAD GASKET PART NO.WAS 4514379-1 OR ANY OTHER ITEMS THAT SHOULD BE ADDRESSED AT THIS TIME
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top