(800) 853-2651
SHOP NOW

Recent content by Joe TAYLOR

Yesterday's Tractor Forums
  1. J

    How to properly use a brush hog

    Thanks Tim that is a very well written and eye opening explanation of useing a brush hog. I appreciate it very much.
  2. J

    How to properly use a brush hog

    Thanks again Dell you have been a great help.
  3. J

    How to properly use a brush hog

    Thanks guys. One more question Dell how do you connect the stableizer chains on your lift?
  4. J

    How to properly use a brush hog

    This may be a dumb question but I would like to know the proper way to use a brush hog. Is the front of the brush hog supposed to slide on the ground or should it be lifted slightly.Thanks a lot you guys have taught me a lot in the past two months since I found this web site Joe Taylor in Texas
  5. J

    9N HYDRAULIC PROBLEM

    I would like to thank each one of you guys for your help. I went out this morning and found that the fork had come off the exhaust vale again so I put it back on and used a piece of wire around the fork and now it works like a charm. You guys are better than pockets on a shirt. Thanks again.
  6. J

    9N HYDRAULIC PROBLEM

    Thanks guys I will try your suggestions in the morning.Thanks very much for your help.
  7. J

    9N HYDRAULIC PROBLEM

    I took the inspection cover off of the right side and the fork was off of the "T" valve and I put it back on thinking that it was the problem.I started the tractor and the lift went up immediately but when I tried to lower it nothing happened.I took the left cover off and the fork was off on the...
  8. J

    9N HYDRAULIC PROBLEM

    After recieveing great advice from you guys on no fire I have now got it running great, but now I have a new problem. I HAD a load of gravel that I spread and just as I was finishing my lift quit working.I found that I was way over full with the hydraulic oil so I drained it out this morning to...
  9. J

    9n Ford won't start

    I really want to thank Paul in Edmonton,H.Cooke and Bruce Va. for your help. Each one of you gave me the same advice and I changed the plugs this morning and it started instantly with out even chokeing it.I really appreciate your help.
  10. J

    9n Ford won't start

    I have a 1939 9n that I have replaced the plugs,points,condenser,plug wires,rotor,coil and carburator.I was doing some gradeing with it and it was running fine.It surged one time like it was running out of gas then back fired loudly.I put more gas in it and it fired right up and ran a for about...
  11. J

    OT Me

    Sir this is my first time to read this foum and I am very sorry to hear of your sickness.I have already said a prayer for youbut after reading all of these replies I think you must be a very special person and I know that God is right there with you. Good luck and my prayers are with you. Joe...
  12. J

    9n FORD TRACTOR WILL NOT START

    I HAVE PUT NEW PLUGS ,WIRES,COIL,POINTS,CONDENSER,ROTOR CAP,DISTRIBUTOR CAP AND NEW CARBURATOR. TRACTOR WAS RUNNING GREATAND i WAS DOING SOME GRADING.iT SPUTTERED LIKE IT RUN OUT OF GAS AND BACK FIRED AND STOPPED RUNNING.iPUT MORE GAS IN IT AND IT RAN FOR A FEW MINUTES AND STOPPED AGAIN.iHAVE...
  13. J

    no fire to the plugs

    Are the spring straps on the points supposed to ground to the base plate of the points are should there be fiber washer between the straps and the base plate of the points.Thanks for your help.
  14. J

    no fire to the plugs

    The points are set correctly and I have fire to the top of the coil.could it be the way that the points are attached to the base part of the points'
  15. J

    no fire to the plugs

    I have a 1939 ford 9n tractor that I have replaced the plugs,points,condensr,coil,plug wires and distributor cap and rotor and I still am not getting any fire to the plugs. Any suggestions on what the problem could be would be greatly appreciated.Thanks for any help you might give me.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top