(800) 853-2651
SHOP NOW

Recent content by joel overturf

Yesterday's Tractor Forums
  1. R

    300 U

    Just bought this tractor for a repair project. Motor is loose but needs a lot of TLC along the way. In my mulling it over I am thinking I should start at the front and remove parts until I get to the rear end. The clutch doesn't seem to work and when they loaded it by picking it up water ran out...
  2. R

    Master Cylinder repair.

    Ok, I'm working on a forklift for a guy and he got the kit but I haven't seen it yet. Is there a plastic sleeve included, to install the rubber cups? Last time I did one was a long time ago. It looks like it would be easy to damage the cups on the sharp edges of the bore. Also I don't know the...
  3. G

    1977 Kubota L185DT Transmission Fluid

    Hello, In my Operators Manual, there is an arrow pointing to an area on the left side of the tractor, and in front of the clutch pedal. There are two bolts where the arrow points. Can anyone here tell me which bolt is the transmission oil fill check bolt? Don't want to remove the wrong one, only...
  4. 3

    Propane tank

    Brother has a tank filled by a company. The tank now has a lock fitting on the outlet side. He hooked my transfer tank, I used to fill my tractor when I was using propane, to get gas to the house. He has the hose to the regulator hooked up from the liquid outlet of the tank. Should the regulator...
  5. D

    Electric start conversion for a JD A

    My neighbor wants to convert his hand start A to an electric start. Are there aftermarket conversion kits available? Told him I would check on the forum and let him know. Thanks for any help. Email is open. P.S. An after thought-- does the factory still have these kits available?
  6. 4

    48 JD A questions

    I'm looking at a 48A. First what # carb is suppose to be on that tractor. Its a gas tractor. Second is the block the same as my 50A? Thanks for the help. ED
  7. B

    Float Setting Zenith 13794

    Can anyone give me some pointers on setting the Float on my FCub Zenith Carb #13794. When I turn my gas on fuel runs out the drain on the carb and I can't find anything wrong with the float.Thanks
  8. C

    air carb hose

    look at the hose from air cleaner to carb. When i insaed it it was dead straight everything was tightend down after a few hours of running why is the hose offset like the aurfilter is sagging its not
  9. B

    Web Site Runnung Slow Or Not

    It takes a minute or longer to open a post.... Everything else I do on my computer works fine and quick. Been doing this for about two weeks.
  10. M

    OT- Appalachian trailers

    Thinking about buying a deck over 12000lb Appalachian trailer. Anybody own one? Just wondering if there any good.Thanks
  11. N

    rrlund! Look what I found!

    Didn't really think I'd spot it!
  12. J

    2840 fuel gauge

    How can I test a fuel gauge? I have 12 volts going to sender, roughly 1/4 to 1/3 tank of fuel and the sender reads 48 ohms to ground. Tech manual says 0 ohms empty and 180 ohms full. Manual says to use a gauge tester or a known good sending unit to test gauge. I have neither. It is no big deal...
  13. T

    8N Rear Hub

    I have a leaking axle seal and am replacing it. My hub is tight, but has a wear ring against the seal. How much is tolerable, and is there such a thing as a sleeve for this? Also, do I have to remove the plate the seal rests in, or does it go in from the outside? I can"t really tell. Thanks
  14. M

    tappet clearance limits

    Forum Members, Was running the R2 Cat on Tuesday I noticed a complete miss when running. When repairing it two years I noticed the tappet clearance was quite over tolerance by about four times. Would have adjusted the tappets to correct clearance but the adjusting screws and locks appeared too...
  15. H

    John Deere 210 39 Bagger

    Howdy all, Has anyone ever seen or attempted to add a bagger to a John Deere 39" deck on the 200 series tractors? I have searched and searched the net and all I found was that the 47" deck could be fitted with a bagger. If I could only find a lower bagger tube (from a JD, Craftsman, MTD...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top