(800) 853-2651
SHOP NOW

Recent content by jon f mn

Yesterday's Tractor Forums
  1. jon f mn

    Combined barley

    The dogs followed me or Bonnie who was raking all afternoon. They would follow me for a few rounds then go to the other field and follow Bonnie for a few.
  2. jon f mn

    Combined barley

    Finally got dine with barley combining yesterday. Yield was down a lot due to the hail damage but not as bad as it could have been. Here is a video https://rumble.com/v7dsubo-combining-barley-2026.html
  3. jon f mn

    Combine repair

    The corn was dry by then so no spoilage, luckily. The birds and mice did some damage tho
  4. jon f mn

    Combine repair

    This was stainless as well, stuff from scrapping a milk tank that was in the barn.
  5. jon f mn

    Combine repair

    When i changed the header to get ready for barley i found the feeder house floor had worn through. So I cut out the bad spot and replaced it with new. Of course somewhere along the line I managed to do something to my hand. Looked like the ring finger knuckle was out of place, but the...
  6. jon f mn

    Cut barley yesterday

    Some did, mine has the s.aller 126 engine, but some had the 188
  7. jon f mn

    Cut barley yesterday

    It depends on fertility, but 80 bu is not uncommon around here.
  8. jon f mn

    Cut barley yesterday

    Corn looks ok, we will see how it does.
  9. jon f mn

    Cut barley yesterday

    Yes but some things are to case specs. The cutterbar is at a different angle and some drive parts are heavier duty. Most case models came with case engines.
  10. jon f mn

    Cut barley yesterday

    Yes, let's weeks and green heads dry down. This wasnt bad for weeds but some came up later so done was over ripe and some was a bit green yet. This way the green will dry down and the rope wont drop heads.
  11. jon f mn

    Cut barley yesterday

    Cut my barley yesterday with my 955 swather. There is nothing as pretty as a field of grain ready to cut. Going to try to bale some hay today and hopefully combine this barley by the end of the week.
  12. jon f mn

    Cut barley yesterday

    Is there anything as pretty as barley ready to cut? Spent the day cutting with my 955 slather. Sure wish it was going to yield as much as it looks like, but the hail on the 4th and 7th did a lot of damage. Hope to bale some hay today and maybe combine the barley by Friday.
  13. jon f mn

    Using A Quick Hitch On Older Stuff ?

    I got a quick hitch for my 530 but it doesn't work on most of my tools. My case blade has 3 pin settings so you can tilt it to the side for things like cutting ditches, since those are circular to keep pin spacing the curve prevents use of the quick hitch. My brush mower has a brace under the...
  14. jon f mn

    Proud owner of a Case 830 CK DOM

    To tighten the hand throttle there is a double nut on the shaft at the bottom of the column, you can get at it through the hole in the casting. Just tighten til you get the resistance you want.
  15. jon f mn

    Proud owner of a Case 830 CK DOM

    If you have a running tractor you can jack up one rear wheel and strap the tank to the wheel and let it run for a while. Those dash lights are available from external_link in new York. He posts here and watches this site.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top