(800) 853-2651
SHOP NOW

Recent content by jonny-o

Yesterday's Tractor Forums
  1. J

    My Jubilee starts up fine But when I hit the throttle the engine revs up to high speed. I have...

    My Jubilee starts up fine But when I hit the throttle the engine revs up to high speed. I have to turn it off with the key. It just keeps running up to high throttle. Any ideas?
    • jonny-o
    • Profile post
  2. J

    Super C duals.

    ok thanks ,going out to play now!
  3. J

    Super C duals.

    I have the long style rear axle on my Super C. I want to mount my dual tires on it. Do I need to turn the rim around on the outside tire and also will my weights stillm mount up?Thanks
  4. J

    Super C duals.

    I have the long style rear axle on my Super C. I want to mount my dual tires on it. Do I need to turn the rim around on the outside tire and also will my weights stillm mount up?Thanks
  5. J

    1952 8n lift arms

    Thanks dudes! That left lever was it. First 8N that I've completely restored!. I have 6 other Fords. All are jubilee's ,640's and an 860. I know them inside and out. This 8N tricked me a little! Lol! Thanks loads. I was getting ready to tear her apart again!
  6. J

    1952 8n lift arms

    I'll go now and check it. I'll be back!
  7. J

    1952 8n lift arms

    Yep fluids are fresh
  8. J

    1952 8n lift arms

    [size=18][/size my hydraulic lift arms don't seem to be connected to any thing inside tractor. I can just move them up and down by hand with no resistance felt. Something broke or disconnected? Hydraulics don't work. Just purchased this 8N. Thanks]
  9. J

    1952 8n lift arms

    [size=18][/size my hydraulic lift arms don't seem to be connected to any thing inside tractor. I can just move them up and down by hand with no resistance felt. Something broke or disconnected? Hydraulics don't work. Just purchased this 8N. Thanks]
  10. J

    4400

    OK thanks guys. I sure hope that this is gonna be eazy! Ill post back when I find some thing out. When you say under the dash do you mean under vthe little door panel? Tim thanks for the photo
  11. J

    4400

    ok thanks I will look in my parts manual for that selonoid. Ill post back.
  12. J

    4400

    i used my 4400 for the last three days moveing fill. this mourning it wouldnt start. changed f uel filter. bleed lines,pumped prime lever made sure fuel lines were clear. if i wiff it with starting fluid it will run . is starting fluid safe to use? somehow im not getting anyfuel. any ideas?
  13. J

    super a

    The tractor was replaced with the original generator wound to 12v and they added a voltage regulator.I haven't had a chance to trace wiring yet
  14. J

    super a

    thanks loads.i will work on it today and post back
  15. J

    super a

    thanks i will give you a call in the mourning
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top