(800) 853-2651
SHOP NOW

Recent content by jpc199

Yesterday's Tractor Forums
  1. J

    mcv flow divider valve

    Thanks for your reply. So far the rest of the rebuild is going good except for taking out this valve. It doesn't seem to have any o rings and the spring can be replaced without taking it out so do I even need to take it out? Could it possibly be stuck, the problem I was having with the...
  2. J

    mcv flow divider valve

    i'm putting a new mcv pump as well as rebuilding the mcv with new springs and o rings on my 1086. i cant seem to get the flow divider valve to come out of the mcv can anyone tell me how to get it to come out? thanks very much
  3. J

    m w turbo not turning

    I have a tractor with a m & w turbo that has been sitting for over a year I noticed that u couldn't hear the turbo so I pulled off the air inlet and can see that the intake fins aren't turning it was working when it last ran so it must of seized up while sitting does anyone know how I can free...
  4. J

    pump for 856 mcv

    thanks I appreciate thehelp
  5. J

    pump for 856 mcv

    I was wondering if the pump for the 86 series would fit maybe its a 13 gpm its had a lot of problems with poor steering and the ta not engaging half the time. when it does engage it works without slipping I can hold the brakes down and stall the tractor but other times it will only move an inch...
  6. J

    pump for 856 mcv

    i was wondering if I can put a 12 gpm mcv pump in my 856 instead of the 9 gpm and if it will just bolt right on or not thanks for any help
  7. J

    antifreeze in motor oil

    I have a 856 that when I took out the oil pan plug to change the oil antifreeze came out what can cause this thanks
  8. J

    deutz dx130 slipping

    thank you I will look into this and see what I can find... do u know anything about the Powermatic can that slip like a ta on a international tractor? or if the hydraulic pump is bad will that cause something to slip? I'm also wondering about the actual clutch slipping again already is there...
  9. J

    deutz dx130 slipping

    hi I have a question about a deutz dx 130 I had a new clutch put in it a year ago at a repair shop and only did light work with it since. it acts like the clutch is slipping again so I took it back to the repair shop but since they don't specialize in deutz they don't know whats going on. is...
  10. J

    high low range transmission cover on 1086

    thanks tractor vet I'm putting the shift kit in because the shift lever was getting jammed up... when I got the shifting assembly off the tractor I noticed what was happening is when u move the lever for high, lo, park and reverse all three functions were trying to happen at the same time it...
  11. J

    high low range transmission cover on 1086

    thanks guys I was thinking about not putting that tank back on if I had to pull it off ....what about the hytran do I have to drain it to take off the side cover?... also I was reading about a special tool for this job if I pull the cover do I still need the tool
  12. J

    high low range transmission cover on 1086

    I'm going to put new detent rollers and spring on the high low transmission cover of my 1086. I'm ready to pull the cover do I need to take off the side fuel tank and remove the side cover as well. also do I need a special tool for this or is there a way to do it without it thanks for any help
  13. J

    1086 hy tran leak

    thanks I will probably split this tractor in about a month when I have the chance and I might be back to ask u some more questions when I get into it . itdid seem to leak worse when the pto was being used I have just been adding more hytran and still using it but its starting to get expensive...
  14. J

    1086 hy tran leak

    my 1086 is leaking hy tran from under the clutch area I'm guessing there must be a seal between the clutch and transmission gone bad. is that something that can be replaced by splitting the tractor at the clutch is there any other possibility for the leak it only leaks when it is running...
  15. J

    856 bad rear end

    I have a 856 with rear end trouble but runs really well I was thinking about finding a salvage tractor with a good rear end and possibly switching to make 1 good tractor which models would this work with...just another 856 or possibly others.. I know of a 826 hydro with a bad engine but not sure...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top