(800) 853-2651
SHOP NOW

Recent content by Ken yn2000-HT

Yesterday's Tractor Forums
  1. K

    hydraulic issue

    I have the same tractor and had same problems. I replaced the springs in all of the valves and tightened up some slack or wear in the three point control system that works the control valve. I have two hours working the pond scoop so far and it works like it was supposed to. I believe 35-40...
  2. K

    hydraulic issue

    I have the same ym2000 tractor with the same problem. I have been lurking in the background and reading all the good ideas for months, I work the tractor about an hour and go to the shop and let it cool down. I replaced my pump and have the same problem. I switched my o-ring to the edge of...
  3. K

    Differential Pedal, YM2000

    I removed the top of the PTO assembly, and assumed the roll pin was sheared at the fork. it was gone. I used a long flexable magnet and fished for pieces of the pin with no luck, I found a lot of normal filings of metal, I blew air into the case, hoping to dislodge any big pieces, I poured...
  4. K

    Differential Pedal, YM2000

    Winston, I was pulling a bucket load of mud out of a pond when one wheel started to spin, I stopped, put my heel on the lock and it went to the floor. It can be raised by hand, moved up and down and feels disconnected. As Alan suggested, I'm concerned about loose metal in the system doing...
  5. K

    Differential Pedal, YM2000

    I have something broken internally. The pedal is loose or not connected to anything. The roll pin that can be seen on the outside of the shaft is intact. I think I may have sheared a pin on the inside or something worse. In the service manual (p65) it shows a "special tool being used. Can...
  6. K

    Shes down...again! Black smok and knocking sound

    Dont give up yet, my ym2000, blows black smoke, loses power about every two years, its old and has a lot of hours and other problems but,,,,, I clean the muffler or replace it and it goes another 1000 hours. Take the muffler off, if it runs and stops smoking you may get lucky and only need a...
  7. K

    Lift arm pin damage

    Thanks Norm, I used the ole JB trick about three years ago too, but now I have about a 1/4 inch long crack about 1/8 inch wide. I feel like I have abused my baby.
  8. K

    Lift arm pin damage

    I cracked the housing where the lift arm pin screws into and connects the lift arm to my Ym2000 tractor. Can this metal be welded and new threads cut, or have I a bigger problem?
  9. K

    stopped up muffler

    My old YM2000 completely stops up the muffler about every180 hours, I ordered a new one, but I want to salvage or clean the oldest one out. Can someone tell me how they might have done this or what they used?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top