Recent content by kennyhatcher

  1. K

    Ford 7000 duel power Maintains absolutely no pressure

    I have a Ford 7000 with Dual power that maintains absolutely zero pressure plugging off line from the pump I automatically get 180 pounds of pressure the tractor will not move forward or backwards what are the possibilities of where it s leaking Clutch plates and seals look good
  2. K

    ford 7000 duel power and pto

    Thank you, sorry about the confusion but I did not see the first responds. Thank you again.
  3. K

    ford 7000 duel power and pto

    hello on a 7000 ford. by removing the cover plate and gear shefters on the transmission, can you see the duel power clutch and the duel power valve ???????
  4. K

    pto problem ford 7000

    This message is a reply to an archived post by kennyhatcher on July 02, 2016 at 13:06:36. The original subject was "pto problem ford 7000". hello The pto works as long as duel power is on the low side so does anybody known if you take the cover plate on top of the transmission, the plate that...
  5. K

    ford 7000 pto

    Ok I got the ford 7000 put back together. the PTO works when engaged and off when disengaged . But when you put the tractor on high side of the duel power the PTO starts to turn. I'm really confused on this because the little pump puts pressure to the duel power and PTO through different lines...
  6. K

    ford 7000 pto

    Hi Again Ok I took the clutch pack apart ,removed the compressing piston return spring. But I cannot get the piston to move, I put air (110-psi) to the hole in the clutch housing hub but the air leaks around the out side seal of the piston. I took my old one apart and it came right out with the...
  7. K

    ford 7000 pto

    Thanks I pulled the support off the clutch pack and tried the air direct to the holes in the back of the clutch pack. you can hear the air leaking by and I can still turn the hub inside the clutch. one hole you can hear the air coming in to the clutch and the other hole the air comes out the...
  8. K

    ford 7000 pto

    thanks sounds like a good ideal
  9. K

    ford 7000 pto

    Thanks
  10. K

    ford 7000 pto

    should I go ahead and get a new support and valve system for it. I took it over to my sons shop and he has 150psi air did the same thing filled hose with oil then put air pressure to it and i could still turn hub inside clutch pack setting on the bench.
  11. K

    ford 7000 pto

    before i split the tractor I tested the line out put to the duel power which is the same pump and had 150 to 170 psi. my tractor does have two pins, the book say too tight back one first then front and 2 - 5 foot pounds. before I split the tractor I took side cover off and it looked like the...
  12. K

    ford 7000 pto

    I filled the line with oil and hooked my air(110 psi). I can still turn the hub gear inside the clutch pack there is oil leaking out between the valve and support, between support and clutch close to the clutch side. and out around the control rod by the clip . I cannot feel any groves in the...
  13. K

    ford 7000 pto

    I have a 7000 ford split working on the pto have installed new pto clutch but the control valve and the support leak I hooked my air too the valve and it leaks is this anykind normal I need all the help I can get the books I have are pretty vague.
  14. K

    pto problem ford 7000

    we where working on are square baler today and only had the ford to get it out of the barn so we hooked up the pto just to help work the baler and the pto started then would't turn over at all. could that new clutch be shot already.
  15. K

    pto problem ford 7000

    Thank you. I split the tractor and put in a new gear and pto clutch assembly is there any adjustments for oil psi or valve control doesn't look like one ?????
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top