(800) 853-2651
SHOP NOW

Recent content by Kris Peterson

Yesterday's Tractor Forums
  1. N

    1951 Ford 8n will not start

    I have been having an issue with getting my 8n started. It started fine an ran it for a while then it just stopped and would not start again. I have changed the points, condenser, cap, rotor, plug wires and plugs and have had no luck. I have spark and the compression is good, at a loss for what...
  2. K

    fox's and coons

    .17 Hornet works great.
  3. K

    StainlessSteel bolts

    Since we're on the subject,Cat has plated bolts available.Rust resistant,high strength,probably better than stainless.Except for marine use work pretty good.I always use never seize on every bolt except bolts that recommend thread lock.
  4. K

    Recycling parts

    The way I heard it,Talk of restricting sale of used parts and engines by recyclers{wreckers} and part suppliers of older engines by taxes and subsidies.So much for recycling being good for the environment.
  5. K

    Recycling parts

    I,ve heard rumors of govt,[probably EPA ]starting to put restrictions on reusing older non emission engines in cars and trucks.Any one heard of this?It may eventually apply to tractors.
  6. K

    Tractor Hauler

    Thanks;I,m Canadian,not right up on your smog rules.
  7. K

    Tractor Hauler

    To tiresntracks:why will it become illegal in California,because of age?
  8. K

    Tonights topic...

    Live in Northwest Territories,Canada.Both parents from Iceland.
  9. K

    OT-a Leroi compressor

    I know this is not about tractors;but there is a lot of experience available here.i am working on a compressor;Leroi 214 powered by a 4 cyl. Perkins.I am looking for a diagram to connect the air lines.Control to engine speed and compressor unload.I sure would appreciate any help or links to...
  10. K

    Word to the Wise:

    WTF is "bayonet"?
  11. K

    value of super 66 diesel

    Mr.Schwiebert;what is the screwdriver test?
  12. K

    4490 coolant problem

    I have a4490;willwork all day;no overheating;When I stop and go to low idle;pukes about 4-8 L of ccoolant out.An ideas?Thanks in advance for any help;it will sure be appreciated.
  13. K

    cooling parts

    Does anyone here know a good method to cool parts for press fit assembly.I used CO2 before;but our shop doesn't use CO2 extinguishers any more.Thanks for reading.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top