-
Kkshansen replied to the thread Farmall BN problem today.Well I did buy some straight 30 weight oil but might just use that in lawn mower and such. More I think of it the 15W-40 sounds better...
-
Kkshansen replied to the thread Farmall BN problem today.Kind of odd that they actually used a gasket there anyhow. I mean with the pump in the oil pan what would be the problem of a drip or...
-
Kkshansen replied to the thread Farmall BN problem today.Well the tractor is that old but it's "only" been about half that since it was rebuilt! I do agree that now would be the best time to...
-
Kkshansen replied to the thread Farmall BN problem today.My head gasket is not a graphite gasket, it's what I would call an old style with two layers steel with a layer of "paper" between them...
-
Kkshansen replied to the thread Farmall BN problem today.Did not check it, guess I might give it a look before I do put the pan on. The oil pressure gauge stays about half way up most of the...
-
Kkshansen replied to the thread Farmall BN problem today.Any strong preference on oil, guessing just about any 30 weight oils of today are as good or better than what was available back when...
-
Kkshansen replied to the thread Farmall BN problem today.I think I do still have a can of that, I'll check in the morning and see about some if I don't! Do you suggest spraying both sides of...
-
Kkshansen replied to the thread Farmall BN problem today.Well this days work included pressing the cam gear on, installing the cam and governor drive gear both with timing marks lined up...
-
Kkshansen replied to the thread Farmall BN problem today.Well UPS delivered the parts today! Other than the gasket set they are used parts but then the rest of the tractor is used parts. In a...
-
Kkshansen replied to the thread Super C with a Woods L306 Mower PTO Pulley Diameter.Would not take much to fab them up out of some flat stock with a little help from a hammer!
-
Kkshansen replied to the thread Super C with a Woods L306 Mower PTO Pulley Diameter.The brackets are just some say 1/8 inch flat stock maybe 1 1/4 wide. on mine the right bracket bolts to a stud on the inside of the...
-
-
KNo need to torch up the mixer. The tank can just be strapped over the opening. If need be some angle iron or flat iron can be bolted on...
-
Kkshansen replied to the thread Super C with a Woods L306 Mower PTO Pulley Diameter.Not sure if I should send a bunch of pictures to the forum or direct to your email account. Hope some one can let me know! I'll try...
-
-
Kkshansen replied to the thread Super C with a Woods L306 Mower PTO Pulley Diameter.My God, that is a wide tractor! There are many places I mow with my BN that it would never get through! If you need more pictures or...
-
Kkshansen replied to the thread Hey Grandpa…..I doubt it would work due to the size of a Farmall tank but over on some of the motorcycle forums there are people who use a cement...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy