Recent content by Lukesdad

  1. L

    7740 steering issue

    I picked up a bale of hay and checked it at standstill (instead of rolling) and it wouldn't turn. At standstill with the left hand turn in motion, the low pressure side cylinder port showed a high flow of oil. (Same port no flow with steeing wheel not in motion). I also tried the same test...
  2. L

    7740 steering issue

    Thank you for the feedback and suggestion.
  3. L

    7740 steering issue

    I did a quick search through archives and didn't come up with anything on this, but I could have missed something. I have a 7740 S that loses steering intermittently when steering left. The steering wheel will continue to turn and the wheel cylinder / wheels will not. Sometimes but not all, I...
  4. L

    Help! Removing Engine Block David Brown 990

    Trying to remove the block from a 990 selectomatic. I don't know how the block comes off, looks like it's doweled to the frame on the bottom. If anybody can give any pointers I would appreciate it. See photo to see how far I am into it. I don't want to force something and stress the block.
  5. L

    8630 Funk Tranny Issues

    Please help. Throwing random P codes every so often when I use the inching pedal (not all the time). First thought it was a grounding issue, but now sometimes the inching pedal won"t inch the tractor, have to let it all of the way out and then it lunges. This is sporadic, sometimes it works...
  6. L

    Ford 40 series block heater needed

    Can anyone tell me the best option for adding a cold weather heater to a 40 series ford (7740). The thermal start doesn't cut the mustard when it gets cold. Freeze plug heater? Thanks
  7. L

    8630 random trans codes

    The transmission on my 8630 is throwing miscellaneous codes in fwd, rev (more in rev), and while using the inching pedal. They are not repeatable, i.e. ocurring at the same instance every time. Does anybody have any experience? I have been through the book on one of them and found no issues. I...
  8. L

    8630 loping at low idle

    Bought a 8630 last fall and getting ready for hay season this spring/summer. For some reason the tractor will lope (if I let it lope it gets to the point where it will rock the tractor a little - pretty aggressive). Doesn"t miss, sputter, etc, just lopes at low idle. If I speed up it a bit...
  9. L

    240 PTO seal removal?

    How do you remove the PTO seal on a 240 utility? Does the whole housing have to come off? Thanks for any help.
  10. L

    IT Manual for 30 series same as TW?

    I assume I&T manual doesn't exist for the larger 30 series Ford since I can't find any. Does anyone know if the TW series I&T manual would work? I realize the powershift wouldn't be in there along with a few other things but I'm wondering if there are other options than the very expensive...
  11. L

    Re-sleeve MF150 (Z145) or not

    Need some advice - having trouble making up my mind - this is my first rebuild. Have a MF150 w Cont"l Z145 that had a lot of blowby - even oil coming out of the spark plug on #1, #4. Tore it down and found compression rings way out of spec (gap) and a few were ~5-6 thous over on the ring side...
  12. L

    Cummins Diesel (Dodge) questions

    I know there are some dodge/cummins websites, but I need some no nonsense feedback. I have a 2001 dodge diesel that"s got a little over 100k. Not had to do any work to it except for standard stuff (fuel/oil filters, grease, etc). Is there any specific things I should replace with this many...
  13. L

    Setting Valves on MF275 where is TDC?

    Thanks. I'm as about as shadetree as they come, but I think I follow you guys. Basically rotate until both valves are fully closed (rocker rocks) and you can set the gap on that cylinder. Sounds like the experienced don't even use flywheel marks.
  14. L

    Setting Valves on MF275 where is TDC?

    I'm trying to set the rocker arm/valve clearance on a MF275. The TI manual says to use the timing marks which have TDC1 and the other TDC4. I don't have these marks. Here's what I appear to have. 2 sets of single marks (180 degrees apart? - can't tell) 2 sets of double marks (again maybe 180...
Yesterday's Tractor Forums

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Back
Top