(800) 853-2651
SHOP NOW

Recent content by macec3

Yesterday's Tractor Forums
  1. M

    5610 Ford front support casting removal

    5610 Ford. Trying to remove the front support casting. It is above the front axle. The front axle pivots on the bottom of the casting. Got everything off except the axle. Front pivot pin is being stubborn. Haven't tried heat yet. Any advice on removing the front pivot pin would be appreciated. I...
    • macec3
    • Thread
    • Replies: 1
    • Forum: Ford
  2. M

    7600 steering column

    Alexander's Tractor Parts in Winnsboro, TX. rebuilt one just like that for me. (800) 231-6876 It ain't cheap either.
  3. M

    Ford 5610

    I have two of those Fords. A 5610 bought new in 1981 and a 5610 II bought in 2013 with 725 hours on it. Both have been very good tractors.
  4. M

    Stuck clutch

    I have strapped the clutch pedal down with a bungee cord. Get on and drive it. Went thru a little dip in the pasture and mine came loose. Apply brake while driving might break it loose.
  5. M

    Oh this is even better. Backhoe wood splitter

    Worked with a logger years ago. Some time we would end up with a short piece of oak. The loader operator would pinch it with the grapple and split it. He had a wood heater. Took all the work out of firewood processing.
  6. M

    Seen It All Yet?

    There are videos on YouTube of people doing that to Farmall and Allis Chalmers tractors. They are using the Predator engines from Harbor Freight.
  7. M

    Cost of new holland parts

    Recently bought 2 o-rings from NH dealer. $24.50 for the pair. They are about 1 OD. Outrageous price IMO.
  8. M

    3pt tiller

    I have a 7' King Kutter from Atwoods. It has done a good job for me.
  9. M

    I hate birds again

    I had a problem with birds roosting on the structure above my truck. Got one of the plastic hawk decoys. Don't get the owl. Now he sits on the bed of my truck. No more poop on the truck. You may want to put one in a visible place near your tractor shed.
  10. M

    Square Baling 1st Cut Thin Hay

    When I have thin hay, I will rake a couple of windrows together. Cuts down on the baling time.
  11. M

    when to use Tedder

    If the hay is thick, I tedder it the next day.
  12. M

    68 5000 8 speed neutral safety switch help

    Sounds like a similar problem I had on a 5610. The spring, plunger and ball all work together. The parts you are missing are in the bottom of the transmission. I attached a magnet to a rubber hose and snaked it down along the inside of the transmission and under all the gears and shafts. Did not...
  13. M

    Clearing a plugged grease fitting

    On an old grease fitting, I have seen the spring rust away leaving only the ball. When grease is applied the ball is pushed back and acts as a plug. Probably easier to just change the zerk and be done with it.
  14. M

    Favorite Ford Tractor

    I have a 5610 with a loader and a 5610 series II. I like them both.
  15. M

    Sell it or Keep it

    Keep it. Tractors like that are hard and probably impossible to replace.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top