-
Mark EC.IN replied to the thread IH 706 Converting 2 pt fast to 3 pt. Is it worth the cost and work?.I've used this setup for years. If you want to use it on a bush hog or cultivator, it works fine; if you want to moldboard plow, it... -
-
Mark EC.IN replied to the thread Some starting help needed..You have a bad connection at the battery. Clean the posts and the cables, then give it another try If that doesn't work, try jumper...
-
Mark EC.IN replied to the thread John deere 95 corn settings.I'm curious where you are located that you have mature corn this early. I'm in Indiana, and we are still operating off the "knee high...
-
Mark EC.IN replied to the thread John deere 95 corn settings.I agree, you can overload the sieves and throw corn out, but it takes damaged corn to blow it out with too high a fan speed.
-
Mark EC.IN replied to the thread Should I buy it?.If the day comes when you move some dirt, make sure to start a new thread so it catches our attention. Just my opinion, but I can see...
-
Mark EC.IN replied to the thread Plow day.You might check with the "man in charge," but I don't see why anyone would object.
-
Mark EC.IN replied to the thread Should I buy it?.You have said you are a pretty good mechanic, and I bet you will be a better mechanic in a few months if you buy it. But I bet you will...
-
Mark EC.IN replied to the thread John deere 95 corn settings.I've never run a 95, although I have run a 105 and many other machines, mostly MF before the IH Rotaries came out. Anyway, to answer...
-
Mark EC.IN replied to the thread Hours of work..Amen! Back here in Indiana after 30 years, all you have is some brown, rusty powder on the ground where it was parked.
-
Mark EC.IN replied to the thread Hours of work..Bushels have more to do with holes wearing through metal than hours. Looks like there was some rust going on there also.
-
Mark EC.IN replied to the thread Farmall 806 Diesel.Make sure the neutral safety starting switch is working as it should; it is on the clutch linkage.
-
Mark EC.IN replied to the thread Nice looking JD45 at an auction in Osceola IA May 30.Link: https://www.allamerican-auctions.com/auctions/public-auction-retirement-of-jane-floyd-buttrey/
-
Mark EC.IN replied to the thread How to measure plow bottoms?.Measure from center to center on the main beams, the beams that the bottoms are attached to.
-
Mark EC.IN replied to the thread Hi.If the will fit the rims I don't see why not. I've ran old car tires on tractor fronts, wagons, and many othere implements before.
-
Mark EC.IN replied to the thread 806 with PTO powered AC.Never heard of such a set-up. Hopefully, you got some pictures.
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy