-
ExpiredFor sale 1941 JD B battery box side panels
Bought these from the original owner ....$120.00 -
M
821/4000?...pto question ....
Thanks as I was hoping I would not have to do that too...just was not sure if when shifting the lever if it would be in the way.. So have you ever had your tractor pto out ? -
M
821/4000?...pto question ....
yes well ten I can forget taking the main out and just hoping the sprocket that has been installed for whatever it ran...wont be in the way of the shifting operation for the pto....and since I have the top off the seat I can put my hands right down inside to guide the new pto shaft with the... -
M
821/4000?...pto question ....
Im not going to split the tractor...unless there is another way..I agree to find the housing from someone and use the JUST parts I need...I also believe that Ford from the factory even though it did not come with the PTO attachment they still put all the parts in the housing and all someone... -
M
821/4000?...pto question ....
so I just knocked the welch plug out and didnt think to look if there was a bearing...or seal....so tomorrow I will look...I did drain all the oil but some did not come out and when I was fishing around in the oil for 5 minutes looking for the welch plug I did not find anything else.. ... -
M
821/4000?...pto question ....
Thanks for that info....now that I have looked at some pctures on computer I see the setup....so what I need is aPTO shaft with all the bearings and seals ect and I can get a new one complete .....and I will need a shifter plate assembly ,,,,,,and A shifter rail and the stop fork and the nut... -
M
821/4000?...pto question ....
Ok thanks for the diagram....so are yiu saying then that I have a hundred series rearend then ok .....and the tractor was built in late 1961 then thats helpful...thanks...!, And so with the pictures I put on here ...your thinking I will need the complete shaft and bearings and seals... -
M
821/4000?...pto question ....
I dont get it ...the lever is missing ...and the shaft ...I guess I would have to see a diagram ...I tried to go to that website...cant seem to even find what I am seeking..,,that is too confusing....they need to make it easier to use....thanks for the help but that is the worst web site I... -
M
821/4000?...pto question ....
I think a forklift mast ...but the seat does not allow you to turn around and no levers for that either...So I really dont know why it was on here,,, -
M
821/4000?...pto question ....
Idid what you said and yes I see the spline from the trans thru the shift lever removal...Now the big welsh plug needs to e kknout out and somehoe find a correct length of a PO shaft and a shift lever cover ...I dont think I have the 100 series rear end but a !000 series...so that I hope I can... -
M
821/4000?...pto question ....
well here are the pics and your were right.... just like you said there was a Zomie setup under the fluid ......by removing the left side round cover where to Lever should be I can see the spline inside a cast tube ....and also the welch plug that would need to be knocked out so I could... -
M
821/4000?...pto question ....
I just trying to see if I can put a PTO in this tractor if I remove the shaft thats in it now? I know I would need the left side round cover wth the lever to engage it but is there more than that to make it work? -
M
821/4000?...pto question ....
Ok Sean ...so I went back and found some pctures of when I changed the miserable seal and bearing...what a miserable thing to find the right bearing and seal...I remember spendng a week trying to just do that...but I dont have any pics of the gear I was describing to you...but it had to move...
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy