(800) 853-2651
SHOP NOW

Recent content by Matt Compton

Yesterday's Tractor Forums
  1. M

    Hydro 86 hydraulics/hydro sucking air

    Thanks for the reply guys but this problem still exists after the filter change. what about the o-rings around the suction manifold? see as how its causing issues on both hyd pumps? if so how hard is it to get at and do you have to drain all the oil? Also i"m sure you guys will scold me but our...
  2. M

    Hydro 86 hydraulics/hydro sucking air

    Good day I own a hydro 86 that seems to be sucking air causing the hydraulics to be noisy especially when cold, I am from Canada the tractor is stored in the barn all winter and not used but periodicly started and moved outside to keep the batteries charged etc. On cold days the tractor is...
  3. M

    Hydro 86 Backfire UPDATE

    Thanks to all that replyed, removed the filters only to find a small trickle of fuel coming from the line, blew the line out, and presto bango, all better now, and runs like a champ once again, thanks again to all that replyed. <a...
  4. M

    hydro 86 With 310 diesel backfiring all of a sudden

    That's what I was figuring on, the tractor is the nicest running tractor I have ever owned, it just happened out of the blue. Tractor still starts on a dime. I all happens above 1200rpm
  5. M

    hydro 86 With 310 diesel backfiring all of a sudden

    Well I was having a great day on my hydro 86 when all of a sudden out of the blue it began to backfire out of the exaust, runs OK at idle to about 1200 rpm, anything above it smokes, and is up and down in its rpm like a yo yo give her a shot of fuel and bang bang bang. It sure sounds like a...
  6. M

    Hydro 86 3-point wont hold position

    Good Morning, recently bought a hydro 86, love the tractor, I could listen to that 310 purr all day long. only issue i have is that the 3 point hitch is not holdings its position, say i had at implement 6 inches off the ground with the tractor running, it would drop about an inch, then lift back...
  7. M

    1650 Input shaft help!!!

    He guys, went to put a clutch in my 1650 and found more wrong then I bargined for, I could shave with the splines on the the input shaft, Cropping season is fast approching and I have more things to get ready then I can handle, I need the tractor, and I dont want to install a new shaft unless I...
  8. M

    1650 Oliver worn out shafts

    Are you referring to the church disk or the chain coupler
  9. M

    1650 Oliver worn out shafts

    Looking at my worn input shaft and grunging at the dollars I wish I didnt have to spend to fix it, there is still lots of good spline behind the worn spot, I see A-I sells a sprocket for a model with out hydra drive, the splines look longer could I not machine this one to fit on the good splines...
  10. M

    Upholstery in a 2255

    Is your cab a factory "ROPS" cab, if you look at my post below, there is my 1755 with factory cab on it, I refurbished the cab, i'd be more then happy to send pictures
  11. M

    1650 Oliver worn out shafts

    Thanks Larry, Do you think the 4 pad clutch is more rugged then the full face, Tractor is going to be a hobby puller down the road
  12. M

    1650 Oliver worn out shafts

    Good day all Finally got time you tear apart the 1650 to install a new main clutch. Got it apart, now I found all the wore out parts. Input shaft, and the pto shaft and coupler are both completely toast. Just the joys and pains of working on old but far from tired iron. Couple questions, and...
  13. M

    1650 PTO Brake

    Thanks J I"ll get you the numbers. But the motor was replaced in the tractor so I"ll look for a number off the hydrapower.
  14. M

    1650 PTO Brake

    Good evening all, bought a 1650 oliver last summer, we owned a Cockshutt 1650 new on our farm but traded in for a case :-( When I told my father that I was looking at a 1650 he told me a funny story about it that involves driving down the highway with a full load of manure in the spreader and a...
  15. M

    Hydro 86 Temp gauge cluster

    Hey Kent, The trans was toast, Brian at Green Diamond rebuilt it, the 3 point was all to heck too, the bill was over 7000 to get her farm worthy again BUT! A very worth while investment, I LOVE THIS TRACTOR, I wouldnt trade her for the world, plus I would have to get 12000 to break even! A great...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top