-
M
'57 640 Ford Tractor
Ok, Your the master on this subject I guess. Ill just sit back and read from now on. Maybe I"ll learn something. Been in tractor repair for over 35 years and I still don"t know anything I guess but that D-17"s seal isn"t spinnig anymore I guess. Cheaper fix than buying a new bearing retainer if... -
M
'57 640 Ford Tractor
Many times but not on a 640. Not many Fords around here I guess. Just finished one on an Allis D-17 with a loose fitting seal. -
M
'57 640 Ford Tractor
I guess you might say that is just my opinion, I guess. LOL -
M
'57 640 Ford Tractor
This may not apply since you said the shaft is spinning inside the seal but if you find the correct seal is in and is spinning in the housing then the housing may be worn from the seal spinning and a new seal may also fit loose and spin. I have had good success fixing that problem by using a... -
M
'57 640 Ford Tractor
I would guess that using I guess is the same as in my opinion so no more opinions on here I guess. -
M
'57 640 Ford Tractor
J. Franklin, writing my guess is a bad choice of words on here, I guess. LOL I made a post and wrote my guess............... Well that got a member on here upset and this was posted: "We don"t operate on hunches here. We operate on observations and we verify things as we go." So no more using... -
M
G-fan shaft bearing
Any bearing supply store in your area can get them.- McBride
- Post #1
- Forum: Allis-Chalmers
-
M
FORD 5000 Model # E3414E
Don"t Know. My book does not list a 34 code under chassis. E3414E E- Later built model 5000 34- ???? 1- Diesel 4- Independent 540 PTO E-Select-O-Speed transmission -
M
Where would one find the serial number on a 4000?
Both 4000"s should have the number in the same place. I said transmission but clutch housing or bell housing should be the location on the right side. -
M
Where would one find the serial number on a 4000?
Look for it on the top of the transmission. -
M
Tractor doesn't have a lot of power
Yes it could. And if the point gap is off the timing will also be off. Both can cause power loss.- McBride
- Post #1
- Forum: Tractor & Farm Talk
-
M
Tractor doesn't have a lot of power
Sounds like timing may be off. Set the points to 0.015 will a feeler gauge.- McBride
- Post #1
- Forum: Tractor & Farm Talk
-
M
Ready to shoot my 2N (Kind of long)
Had a tractor do the same thing once. Points.- McBride
- Post #1
- Forum: Ford 9N, 2N & 8N
We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.
Copyright © 1997-2025 Yesterday's Tractor Co.
All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.
Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy