(800) 853-2651
SHOP NOW

Recent content by mchapin

Yesterday's Tractor Forums
  1. M

    John Deere FB-B Grain Drill Restoration parts needed

    Bought a funnel from JD a couple weeks ago for a FBB. Part number was superseded and the part was described as plastic. But it turned out to be metal and exactly like the old one. I was happy to get it. But then, only needed one.
  2. M

    John Deere 37 Sickle

    Refurbishing a 37 JD sickle. Numerous parts were missing. Having a problem installing the pitman arm. Mainly the spring release Z 7327H. What does it do, and is it nessesary? It looks like the spring release fits into a tab on the Fork,Latch P 47370. My Fork does not have this tab. Parts were...
  3. M

    JD 671 rake

    Thanks for the tips. Is there a good sequence for putting them back together.
  4. M

    JD 671 rake

    Any tricks to rebuilding the tooth bar bearing housing. The knuckle broke. Thought it would be an easy rebuild. Was going to reuse the bearings. How do you get the bearings out without destroying them?
  5. M

    Pecan harvester

    lol
  6. M

    Hesston 1010

    Interesting machine
  7. M

    Hesston 1010

    Did Case have an equivalent.
  8. M

    Pecan harvester

    Yes, will rescue the machine. Any manuals out there?
  9. M

    Pecan harvester

    I did a search for Pecan Harvester auctions. Did a search on the machines that came up. It is a Nut Hustler. With that information, found a U tube. Which confirmed it is a Nut Hustler. Now to find parts or a manual. Thanks for the idea.
  10. M

    Pecan harvester

    Found a pecan harvester in the brush. Looks complete and salvageable. Cannot find any serial number plates. Trying to figure out the manufacture. It is painted blue, possibly manufactured in Lampasas, TX. Thanks for all of the help.
  11. M

    JD 37 sickle

    LOL. small world
  12. M

    JD 37 sickle

    Thanks Bob. Was told the mower came from N. Dakota.
  13. M

    JD 37 sickle

    Why did JD offer 2 flywheel speeds. 850 or 950 at 540 PTO? I assume its crop related, but do not see any reference in the Op manual. Is there a good place to fine used parts?
  14. M

    PTO wood chippers

    I have owned/used several wood chippers. The best one is Woodmax. 8 inches is getting close to its limits though. Feed is hydraulic, slow the feed rate down for the big stuff.
  15. M

    5065e Remote Quick Disconnects very difficult

    My 5083e is also hard to disconnect. Make sure the pressure is bleed off the system. Give a good push and pull.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top