(800) 853-2651
SHOP NOW

Recent content by mike a.

Yesterday's Tractor Forums
  1. M

    Gleaner E engine value

    2 years ago,i paid $350 for a stuck model.salvage yards were getting about $1000.anything less would be a bargain.
  2. M

    TROPHY CHIC !

    lets re-wire,insulate,sheetrock that trophy shed,only then will it be a chic magnate!
  3. M

    Just a thought...

    Amen!
  4. M

    WC Allis brakes

    i moved my seat to the middle of the tractor,rarely do i need to use my brakes at all during the season.also this evens out the weight,no need to offset.i still need to center up my controls.once i changed all this,i would hate to go back.give it a try.
  5. M

    Allis govener

    i would use a gov spring for a 175 allis.it should rev to about 1800 rpm's about $4o from agco.
  6. M

    wd45 pulling help

    ditch the combine gov,use a tractor gov,also spend$40 to buy a175 gov spring,it should rev to 1800 rpm's.good luck!
  7. M

    18.4-38 pressed steel

    i have for sale 18.4x38 goodrich,one-third tread,road-wore,sw minnesota area,please call 507-215-7013.
  8. M

    how many here own a dyno?

    and they say customer service is dead.i wonder why?by the way,i do plan on using a dyno to tune my rebuilt gleaner motor,in my wc chassis,of course.thanks mitch-later.
  9. M

    rebuild specs

    does anybody know the torque specs on a e gleaner,for the main&rod bearings.also head bolt specs?thanks-mike
  10. M

    wd or wd 45??

    my wd-45 engine has shims in it.i believe the i&t shop manual calls for shims also.
  11. M

    sleeves

    i have a pair of rusty sleeves,inside and out.does anybody have a good way to derustify these parts?thanks.
  12. M

    wd sleeves

    thanks mitch-i know i could count on you!
  13. M

    wd sleeves

    will wd sleeves fit in a e gleaner block?they look similar.thanks-
  14. M

    Camshaft and Belhouse

    berry cam in lester prairie,mn can grind your old cam for you.
  15. M

    overbore e-gleaner

    thanks mitch,the machine shop said this is possible.i still have to get 2 pistons removed from my rusty cylinders.one sleeve started to come out on me.the good news is that my crankshaft looked really good-standard bearings!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top