(800) 853-2651
SHOP NOW

Recent content by mike crissman

Yesterday's Tractor Forums
  1. M

    Allis chalmers 653 dozer

    Thanks going to take motor out anybody no if u can rebuild oil or is one still available for it
  2. M

    Allis chalmers 653 dozer

    Oil pressure starts out at 25 pounds run for half hour drops to 2-5 pounds thinking bearings 4 cylinder diesel motor same as hd4 thanks
  3. J

    TO-30 Radius Arm Socket Joint Wear

    I was dragging my pature today when I heard a funny clank at my left foot. When I looked down, I saw the upper bolt that holds the socket for the back of the radius rod was about to fall out. The lower one had fallen out. I could"t leave the tractor in the pasture because the cows would have...
  4. D

    Today's SAV picture

    This is a picture of a toolbar setup on the back of the tractor. It has more than one hitch in it's get-along that's for sure... It has a repair on the left side where it looks bent. Those long arms extend back under the tractor to about the edge of the platform, then articulate back to the...
  5. R

    making you guys with seats jealous

    fired up my snow plow saturday morning.
  6. M

    hd4

    will 14 inch pads work on a hd4 with a bucket thanks mike
  7. R

    Rope counter

    Hi guy's I have a old rope counter that's Said's Columbian Pure Manila Rope Red White & Blue Made in USA. Would like to find some Info Or were to Look Thank You Rod in MN
  8. S

    OT: Microwave won't run

    Last night my m/w stopped working. All the electronics concerning timing, defrosting, clock, etc. still work normally, but when I push the button (keypad) to cook something there is a faint click and then nothing happens. Well, actually, something happens, because the timer counts down the...
  9. S

    4400 corn head drive

    has any one out there had trouble with lower feeder house shaft flexing and throwing off drive chain to corn head,replaced shaft with new one and it still aint right ready to add a pillow blck bearing out near the end of shaft
  10. M

    hd4

    does anyone have any bottom rollers for a hd4 h4 hd3 h3 650 allis chalmers thanks mike
  11. M

    hd4

    will a allis chalmers m bottom roller fit a hd4
  12. M

    hd4

    does anyone know what bottom roller fit in a hd4 or does anyone know where to get some thanks mike
  13. M

    hd4

    i live towards pittsburgh pa could u get me numbers for scrap yards or directions any help would be apreciated thanks mike
  14. M

    hd4

    will allis chalmers m chain work on a hd4 or does anyone know where i can get a set of chains for it thanks mike
  15. L

    70 Dodge car Alt. gauge

    Alternator gauge needle jumps around but everything seems to work and charge, is this just a characteristic and worry not or is there a simple solution for this.Dan
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top