(800) 853-2651
SHOP NOW

Recent content by milkmanNC

Yesterday's Tractor Forums
  1. M

    OT RE: Me

    Even though I don't post here too often... First time I had a problem and posted here you were one of the first to post much needed advice and I want to thank you for your much needed advice. With that said, Prayers are with you and stay positive.
  2. M

    9N hydrolic fluid amount

    So, I need to pull the bottom bolt on my inspection cover and let it sort itself out. :) Thanks for the reply!!
  3. M

    9N hydrolic fluid amount

    I have read on this forum somewhere (can"t find the post in search) that when changing the hydrolic fluid, to pull the rear plug first and work your way up to the front plug. Also seem to remember that it should hold 4 and 3/4 gallon (might be wrong). Well with tractor running and the three...
  4. M

    Wiring 9N - motor keeps running after key is off

    Thanks for walking me thru this. I had to turn the key on or it would not crank. It WILL turn over without the key turned but will not start! Turn the key and it fires right up, but will not cut off.... wigled the wire conector on alt. as to unplug it and it died. I then took the key switch...
  5. M

    Wiring 9N - motor keeps running after key is off

    #2 does go to output stud. Also have a wire that goes to the ammeter from the main output stud. #1 goes to right side of resistor block. I am at a loss here.... thanks
  6. M

    Wiring 9N - motor keeps running after key is off

    ok.... you are right ... kinda I wired the BAT. side of the key switch to the bottom post on my resistor block (battery to starter swich and ammeter also wired to this bottom post). Other side of ammeter is wired to main post on Altenator. I wired the key switch IGN. side to the right side...
  7. M

    Wiring 9N - motor keeps running after key is off

    Wired my tractor to this diagram exactly (top diaagram). Why will my key switch not cut the engine off? Three position switch (bat. Ign. acc.) Had to choke the sucker to kill her power. :) http://www.ytmag.com/cgi-bin/viewit.cgi?bd=nboard&th=746997 Thanks for any advice. Will start without...
  8. M

    Speaking of mufflers

    Exhaust baffles. Motorcycle affles are all over flea-bay.
  9. M

    9N terminal block resistor

    Dell, Since I want to do this wiring corectly, I will not argue and I will order this said part from this great site. I respect your wisedom of sparkie's... Thanks
  10. M

    9N terminal block resistor

    I have began the task of re-wiring my 9N front dist. 12V. While removing the hack job wiring someone in the past did, I removed the small nuts that hold the terminal block resister in place. The porcilin resistor on the terminal block broke. Do I need this in place even though I have an...
  11. M

    OT - Happy New Year What's for Dinner???

    Black eyed peas, collard greeans, hog jawl and cornbread. You mean everybody doesn't eat like us southerner's??? Dang shame I tell ya. :0)
  12. M

    9N wiring harness

    1941 9N 12 volt conversion. I just purchased from this site a new wiring harness. The polite salesperson on the phone said this harness does not come with directions, so... what exactly have I just purchsed and where does it all go? :) My tractor was converted by who know's when and been...
  13. M

    Re: More fun than a human being should be allowed to have

    My grandfather always had Ford tractors, prolly because he owned a dealership (Kabota too) and that Ford's were very popular in Western NC. That being said, I love my 9N. I like tinkering on old stuff, have a very small patch of land that I hobby farm and ofcourse the fact this tractor suits...
  14. M

    Ammeter with a 12 volt altenator

    One wire comes from the altenator... where does the second wire connect to? The short wire was hooked up to thin air and don't know if it hooks up to the ignition switch or not.... Thanks
  15. M

    Ammeter with a 12 volt altenator

    1941 9N front mount distributor and 12 volt altenator. My ammeter does not work on my tractor and for my B-day my darling wife bought me a new ammeter from TSC (good woman I tell ya). Will an ammeter work with a 12 volt system or should I return it and get a volt meter instead? Thanks
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top