(800) 853-2651
SHOP NOW

Recent content by MPM1

Yesterday's Tractor Forums
  1. T

    m and w govenor

    I have a 41 M farmall I pull in the out of field class. I do pretty good as is, but would a m/w governor help more?
  2. M

    case tool

    If anyone is going to have that tool it will be Owatonna Tool Company. They made all the Case Service Tools.
  3. M

    12 volt positive ground?

    Make sure the alternator isn"t internally regulated. And if it is make sure it is working. If that"s the case external regulator will never work.
  4. M

    IH 674 Hydraulic schematic/diagram

    Other than a dealer that still has the old ih books it may be hard to find. What are to trying to find out about the system?
  5. M

    delco remy

    If you order the points by application they will be Delco-Remy
  6. M

    delco remy

    What model tractor? Delco-Remy is not uncommon.
  7. M

    Firing order on MF 65

    FYI Ford industrial fires 1-2-3-4 The only application I ever seen was Blackwelder tomato harvestors.
  8. M

    390T wiring print

    Hi, This tractor has a safty start switch on top of the transmission, and one at the pto lever. They both work in series together. Both need to be working for tractor to start. The one at the pto lever can get debris it the linkage and cause not to fully engage the switch.
  9. M

    2775 Worth

    Wow you never lost one crankshaft?
  10. M

    2775 Worth

    At 1980"s prices the crankshafts were $8000.00 plus labor. And it wasn"t a matter of if it would break but when it would break. If this tractor you are going to look at hasn"t broken a crank the owners have been lucky. The transmissions were also very expensive repair. The brakes would...
  11. M

    265 Chrysler

    FYI: The firing order for all inline 6 cylinder engines is the same 1-5-3-6-2-4.
  12. M

    MF-20C Tac location

    Tach drive is on the back of the engine toward the right side sitting on seat.
  13. M

    TO-35 PTO problem

    The rod looks like the draft control rod from the lift cover. On the pto did you get the lever back in the slot on the shift collar?
  14. M

    concerned person

    Who is this concerned person? OMG what a dip. Only recently found this site, people helping people is what we need more of. It's a great site.
  15. M

    Quick Advise Needed - RE: Machine Shop Work

    If they use a bit type cutter yes there is a chance of chipping the sleeve. If they use a flat wheel decker it should be ok. Are your sleeves pre-bored or do they need bored after they are installed? Some after market sleeves are not sized!!!
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top