(800) 853-2651
SHOP NOW

Recent content by mrfikser

Yesterday's Tractor Forums
  1. M

    super c generator issues..maybe normal, hot

    here is the Super C... minus muffler...and prior to fixing the decals...
  2. M

    super c generator issues..maybe normal, hot

    thanks guys, that is exactly what I was looking for...
  3. M

    super c generator issues..maybe normal, hot

    I have a super c with original 6 volt system.... system seems to be running good.. charging to around (@ 1000rpms) 7+ volts and delivering 2-4 amps to battery (after running for a half hour or so).. My question/ concern is that the generator body stays quite hot...not hot enough to burn the hand...
  4. M

    super c front scraper/snow blade removal/install

    that makes much more sense.. I was removing the whole shabang in one piece... your way is much better.. I was sure there had to be an easiery way to deal with it...thanks
  5. M

    super c front scraper/snow blade removal/install

    works good for grading dirt roads/ 4 wheeler trails etc..knocks the bumps off of the center fills in ruts..light weight work where bigger equip. mostly makes a mess.
  6. M

    super c front scraper/snow blade removal/install

    here is what it looks like
  7. M

    super c front scraper/snow blade removal/install

    my plow looks like this one... when it off the tractor all the attachment points lay in a pile on the ground... am I suppose to leave some parts attached to the tractor?? (i remove the 2 bolts [each side] on the from side mounting plate along with the 2 bolts [each side] on the rearmost...
  8. M

    super c front scraper/snow blade removal/install

    54 super c narrow front .. I have a front snow blade that I would like to know the best way to install remove it.. it is moved up/down by the mid controls.... It works fine, I just want to know the best way to install it/remove it .. such as should I put the blade on a cinder block etc. before...
  9. M

    exposed steel axel coating???

    I found a product called Flood Floetrol... it is designed to be mixed with house paints as a leveler.. I got a tip, that it is good to use straight (not mixed with paint) on bare steel as a preservative... I just happened to have a bottle of it left over from painting my basement walls.. I tried...
  10. M

    54 super c how to adjust govner

    ***okay just an update... I took another look at the situation and found that the accelerator lever on the steering tree has/had a second hole in it, I moved the throttle linkage to the second hole (farther away) and the throttle is responsive closer to the idle end of the movement.....otherwise...
  11. M

    54 super c how to adjust govner

    I took the govnr apart and put in news springs and a shaft seal on the carb end shaft.. everything else looked fine ..so I think I will take your advice and leave well enough alone... 1 quick question, will the first half of the throttle be more used under heavy[er] load??? I was also...
  12. M

    54 super c how to adjust govner

    I'm working on a few bugs for my super c... need info on how to adjust the governor.. the problem is that when you move the throttle control on the steering piller you have to move it around half way (into the middle of its travel) before the throttle rpms goes up from idle, but when you move...
  13. M

    exposed steel axel coating???

    this looks like what i am looking for...i sent them a note for information.. thanks
  14. M

    exposed steel axel coating???

    that sounds interesting/good... but I don't know what 'thread spray ' is...could you post a brand name etc please
  15. M

    exposed steel axel coating???

    I think that needs to be oiled??? to stop rust?? but it would look great, I would think
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top