(800) 853-2651
SHOP NOW

Recent content by MRGJNV

Yesterday's Tractor Forums
  1. M

    Farmall engine

    DAVE Thompson jr, How does Bakers new design work? Not brazed in?
  2. M

    kelly c farmall site

    http://farmallh.freehostingcloud.com/index.html
  3. M

    Chainsaw chain sharpening

    Thanks for the help guy's! I'm on dial up so the big pdf's will have to wait a bit. I have an Oregon 511A sharpener so no filing for me. From what I have read, I think a 25 and 55 degree with a 0 degree tilt should work for me. I have a 20" bar on the 365 and 16" on the 41.
  4. M

    Chainsaw chain sharpening

    I got to sharpen the chains on my Husky 41 and 365 special chainsaws. The manual that came with my sharpener told me what angles to set my sharpener to but foe the life of me can't find the manual. Got to looking on the net for the angles according to the chains I have but there is so many...
  5. M

    Anyone ever use Evaporust? (tank cleaning)

    Put a few handfulls of 1/4" nuts or similar inside the tank and shake the heck out if it for a while. Do this till your happy all the rust is gone. Then maybe try your evaporust again and see how it turns out.
  6. M

    How would you store/protect

    I heat our shop during the day on weekends with a propane torpedo heater. Our SM and H are in there also. Any advice on what should be done to them before attempting to start them in the early summer? They haven't been ran since last fall.
  7. M

    Best Head Gasket

    Hey Goldsburg. Send me an e-mail would ya? Got a few questions for ya if you don"t mind.
  8. M

    farmall 340 (pulling)

    I was sent this idea.
  9. M

    farmall Carbs.

    An 806 carb throttle body or top half is totally different. There is no linkage that connects the governor to the carb. The main jet has an electrical solenoid on it. I'm taking this from the 806 carb I have that I have that is labeled that it came from an 806. Someone more knowledgeable could...
  10. M

    engine pictures

    Post your e-mail as PM's don't work here. Wish they would get that going.
  11. M

    gordyville tire trouble

    Think this is it. WOW! http://www.youtube.com/watch?v=TPv_cxUGwYI
  12. M

    STIHL 880 chain saw

    Hey Dave. What adjustments did you have to do? It would be nice to know what fixed it.
  13. M

    tires wanted

    Looking for a set in eastern Ontario.
  14. M

    M Head Question

    In my uneducated opinion, it's not an LP or 400-450 head. My reasoning is if it was an LP head, it would have crater like holes on the top on the manifold side. You would be able to see them without taking the valve cover off. Second, 400-450 heads didn't have that breather pipe running...
  15. M

    MSD 6a module, worth it?

    care to elaborate on this?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top