Recent content by mrjim

M
8n running rough

Have you been able to solve your problem michaelthorne75? I am having the exact same problem. I have not made any carb adjustments yet. It runs pretty good from idle to about 1300 rpms, then gets rough real quick. Just curious what you came up with. Thanks
- mrjim
- Post #1
- Oct 25, 2017
- Forum: Ford 9N, 2N & 8N
M
8N finally started

Thanks
- mrjim
- Post #1
- Oct 17, 2017
- Forum: Ford 9N, 2N & 8N
M
8N finally started

8N, Side Mount, 6 volt. Cut off on me over two years ago, and I gave up on trying to get it started. Started messing with it again first of October and finally got her started today 10-16. I think a lot of my problem was spark plug and coil wires. I had it serviced at a dealer 3 years ago...
- mrjim
- Thread
- Oct 16, 2017
- Replies: 3
- Forum: Ford 9N, 2N & 8N
M
8n won't start

Thanks, just not able to do that at this time.
- mrjim
- Post #1
- Oct 5, 2017
- Forum: Ford 9N, 2N & 8N
M
8n won't start

I got a plug tester, so I'll test the plugs to see if I have spark. I removed the drain plug from the bottom of the carb and had good flow with gas on 2 turns. I've got to drain the gas again as I now have a leak in the off-on screw of the sediment bowl. After I fix that I'll get back to testing...
- mrjim
- Post #1
- Oct 5, 2017
- Forum: Ford 9N, 2N & 8N
M
8n won't start

Side mount distributor. Positive ground battery. Wiring was replaced a couple of years ago. Starter cranks, just doesn't even try to start. Thanks for responding.
- mrjim
- Post #1
- Oct 5, 2017
- Forum: Ford 9N, 2N & 8N
M
8n won't start

My side mount, 6 volt '51 8n won't start. I drained old gas after it sat for a couple of years, put in new spark plugs (Autolite AL437), new points, distributor cap, rotor, condensor & battery. SOB still doesn't start. Cranks good, have continuity across point when open, key off. have 6volts...
- mrjim
- Thread
- Oct 5, 2017
- Replies: 8
- Forum: Ford 9N, 2N & 8N
M
8N Restart

Thanks
- mrjim
- Post #1
- Sep 22, 2017
- Forum: Ford 9N, 2N & 8N
M
8N Restart

Do you use it at all your gas joints? IE: such as elbow screen where it goes in the carb? or the gas line where it connects to the sediment bowl and the carb? Thanks
- mrjim
- Post #1
- Sep 21, 2017
- Forum: Ford 9N, 2N & 8N
M
8N Restart

Thanks
- mrjim
- Post #1
- Sep 20, 2017
- Forum: Ford 9N, 2N & 8N
M
8N Restart

Drained the gas tank and surprisingly looks pretty clean inside, what I can see shining a light in there (tank is only about 5 years old). Getting ready to reinstall the sediment bowl in the tank. Do I need any kind of sealant on the threads where it goes in the tank? If so, any recommendations...
- mrjim
- Thread
- Sep 20, 2017
- Replies: 6
- Forum: Ford 9N, 2N & 8N
M
Float charger

Turns out I have a Schumaker model 600 automatic charger. Good for 6 or 12 volts with automatic shut off. Is this the same as a float charger? If not, what is the difference? Thanks
- mrjim
- Post #1
- Sep 20, 2017
- Forum: Ford 9N, 2N & 8N
M
Float charger

Turns out I have a Schumaker model 600 automatic charger. Good for 6 or 12 volts with automatic shut off. Is this the same as a float charger? If not, what is the difference? Thanks
- mrjim
- Post #1
- Sep 19, 2017
- Forum: Ford 9N, 2N & 8N
M
Float charger

Thanks
- mrjim
- Post #1
- Sep 19, 2017
- Forum: Ford 9N, 2N & 8N
M
Float charger

Thanks, I'll look for one.
- mrjim
- Post #1
- Sep 19, 2017
- Forum: Ford 9N, 2N & 8N

Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy