(800) 853-2651
SHOP NOW

Recent content by NAAdearborn

Yesterday's Tractor Forums
  1. N

    9N/2N vs 8N governor

    I should ask, can 9N/2N levers be used with the 8N (proofmeter boss) housing?
  2. N

    9N/2N vs 8N governor

    Thanks for the pics, Royse. The levers on this one are about 90 degrees apart, similar to the 9N/2N picture. However, the levers are rotated clockwise about 3/4" compared to the governor that was taken off. It almost has me wondering if the fork was put backwards on the shaft inside of the...
  3. N

    9N/2N vs 8N governor

    Other than the proofmeter boss (and indexing of levers), they look similar.
  4. N

    9N/2N vs 8N governor

    Helping a friend work on a 9N/2N. He bought a "new" governor and the arms do not line up with the previous one when installed. The arm that connects to the carb linkage is off by about 3/4" (putting carb at wide open throttle when it should be closed). Additionally, the throttle lever at the...
  5. N

    A Merry Christmas post for all!!!

    Lets try this again with the picture... Merry Christmas!
  6. N

    A Merry Christmas post for all!!!

    Merry Christmas!
  7. N

    Zane, are you around?

    contact info for Zane.... http://www.bramblett.com/zane/
  8. N

    tie rod nut end hitting radius bar

    Replaced a tie rod end on a 9N and had the same issue. The spindle arm had been broken and welded (not quite straight). Grinding a few threads off the tie rod pin solved the problem.
  9. N

    Little screw press bead breakers any good?

    Kyle, I'll second Royse, I bought the same tool and changed a tire with the rim still on the tractor without any difficulty. Also, get yourself a valve fishing tool with a long length on it.
  10. N

    ring gear heating methods that have worked for you

    I used a bbq grill. Set the ring gear right into the lump hardwood coals, after a couple of minutes the gear was red hot and dropped right on the flywheel.
  11. N

    NAA clutch job parts list?

    Below is a link to photos on an 850 clutch job (courtesy of Jim UT ?), I found this quite helpful when I replaced my NAA clutch. There was no need to undo the steering links. Royse is correct, a pilot bearing is a good idea (note, NAA uses a different size bearing than what comes in the 9N/8N...
  12. N

    Merry Christmas!

    Live in Dearborn, but the tractors (NAA, 9N) live out your way, near Clarksville.
  13. N

    Merry Christmas!

    Merry Christmas everyone. Only my 4th post on this forum, but a regular reader who has learned much from you folks. Brian in Michigan
  14. N

    Air cleaner

    Tip for getting the mesh back into filter housing after cleaning.... Wrap duct tape around the tube end and make a "cone" for the mesh to slide over (helps stop the mesh from hanging up on tube end).
  15. N

    Cheap ORCs?

    Purchased one of the "cheap" plated overrun couplers this spring, $34. 20hrs on it so far with a rotary cutter and a finish mower with no problems.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top