(800) 853-2651
SHOP NOW

Recent content by nathan

Yesterday's Tractor Forums
  1. N

    Transmission slippage on 1086

    I"m new to the tractor and know its been sitting unused in a shed for appx. 10 years. Owner died and we found it so have no history on tractor. Drives but does not have very much spunk and slips, slipping gets worse the longer you drive and it doesn"t make much difference whether or not TA is...
  2. N

    8n rebuild or rings

    operating temp full speed is 20 to 22 and idle it is 1round 10 to 15
  3. N

    8n rebuild or rings

    oil pressure runs around 20 to 25 may drop some after a few hours to 16, 18
  4. N

    8n rebuild or rings

    i have an early 8n with front mount dist, upgraded to 12volt. I have had it for 3yrs used to mow 6 acres and blade driveway. It has lost power and trying to determine if it needs a complete rebuild or rings. or to buy another one and keep it for parts. compression test front of tractor to...
  5. N

    Kohler

    what about the wireing diegram for the K241s
  6. N

    mf 135

    I was able to take the cover off this weekend and found the acuating arm to be free and working.So I drained the fluid to get a good look at everything and found that the pin and rollers on the end of the shaft(going into the hyralic pump and hooks to the bottom of the acuating arm)had fallen...
  7. N

    mf 135

    I do not have oil flow at the plate,where is the o-ring located?Is it on the pipe.
  8. N

    mf 135

    It does not have aux hydralics,I was refering to the large valve body that the seat bolts too.I am now being told to remove the cover on the right side(where the controls and dipstick go in and check for lift cylyinder leak or problem with the linkage of check for free movemant of the2 small...
  9. N

    mf 135

    Hello,I am a motorcycle mechanic by trade but i do not know much about tractors, my father in law has a MF135(perkins)it starts up and drives fine but the hydralics for the three point do not work at all. it has been sitting all winter without use but worked fine last fall. does anybody have an...
  10. N

    8n quit while moving will not start

    I was moving and the brush hog bogged down and the tractor died. It will not restart. I noticed the neg cable was an old car cable so I replaced it and the starter relay and still won't start. this is an 8n with front dist and 6 volts. Could it be the ingition switch. It is not getting...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top