(800) 853-2651
SHOP NOW

Recent content by nl00sb

Yesterday's Tractor Forums
  1. N

    170 engine block identification

    is there a way to id an 170 gas block ? i purchase a pulling tractor and thats whats suposed to be in it but i dont know how to id them
  2. N

    77-880 6 bolt front hubs

    Ide have to have them shipped Im near Rochester NY let me know if u have a set and are willing
  3. N

    77-880 6 bolt front hubs

    iso 6 bolt front hubs for s88 and 880 if anyone has some there willing to part with im looking for a pair
  4. N

    720 power steering fluid ??

    720 rc power steering fluid/oil what is a good fluid / oil to use on these and how much do they take as the front pedistole and pump have been rebuilt ???
  5. N

    d17 diesel series 1-4

    Thanks for the info
  6. N

    45 diesel fitting

    Anyone know the what threads these 90degree fittings on the oil line going into head
  7. N

    d17 diesel series 1-4

    what are the main differences between the different series
  8. N

    2510

    what size plow would a 2510 diesel synchro be rated for
  9. N

    farmall m frontend

    farmall m what narrow front will fit with 6 bolt style hubs ?
  10. N

    6 bolt front to fit M-400

    looking for a narrow front end that will fit on an M what will work and are they any taller or shorter ??? thanks
  11. N

    770 to 880 comparison

    is there any defining things that differ a 770 to an 880 if just looking at pictures ??
  12. N

    USA puller project

    I bet that thing is good for at least 12mph
  13. N

    Oliver 77 3 point value

    What's this 3 point worth ? It's had it share of fixes I'm looking to sell not sure what I should expect to get for it
  14. N

    C153 engine

    a 153 with just basic head work will make 50hp @ 1997 rpms , if you want to build something significantly larger get ahold of cliff s on here , he can surely send you in the right direction , best thing to do is figure out what classes, mph you want to pull and go from there
  15. N

    Unstyled John Deere A Stroke

    I have 7.5 x 5 3/4 in unstyled block with flat head , if I could do it again I would go larger stroke and use styled block and head , u will want to do some head ,manifold porting work and of course do some carb work , will need to degree in the cam , 7.5 is an easy install but your better off...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top