(800) 853-2651
SHOP NOW

Recent content by oldfarmall

Yesterday's Tractor Forums
  1. O

    International 700 plow

    Hello- Looking to upgrade my IH McCormick #60 trailer plow, as I have a bigger tractor now. The #60 plow is a 3 bottom toggle trip with the plow chief bottoms, not super chief. I want to go look at a 4 bottom auto reset International 700 plow with on land gauge wheel. Also know where...
  2. O

    Bearings for disk hubs on IH McCormick Deering double run, high steel wheel feed grain drill.

    Go on Ebay and search IH mccormick grain drill manuals. Try to match up what yours looks like to a manual and model by looking a the listing pictures. For parts, to see if any are available yet, take part number from the manual and google "parts depot". Go to their web page and click on parts...
  3. O

    400 PTO failure

    Swapping PTO units on the 400 is a fairly easy job. Park the tractor on a steep downhill grade to prevent the trans oil from leaking out. There are 4 bolts from what I remember that hold the PTO to the tractor. Take the top 2 bolts out. Make up some 1/2" threaded rod to put into those holes...
  4. O

    GEHL 135 feed grinder parts question

    Yes, my gehl 135 is really wore out, but never had a problem getting feed to the tank with the inlet auger. Wonder if you had some packed feed from last use that was binding up the auger? I would also make sure the slip clutch is working properly on the intake auger sprocket. If you look at...
  5. O

    New Idea 30B sickle mower

    You can look up parts at http://www2.depotparts.com/ go to the parts quick check and type in your part number. If the parts depot has the part in stock, must call your local AGCO (New Idea) dealer to get pricing to order the part Some parts are cheap, and some are so stupid priced, makes you...
  6. O

    GEHL 135 feed grinder parts question

    Hello- I also have a Gehl 135 feed grinder. Replaced the intake auger bearing last year. There is no rear bearing. The rear half of the auger just floats in the conveyor tube to the tank. Take the chain off, unbolt the 4 bolts on the bearing plate, and pull the whole screw out. Pretty easy...
  7. O

    Interesting issue with the 45 baler....

    I have read that the knotter shaft can twist slightly on the 45 balers. This could be why your twine disc timing is off from the good knotter. -Jesse
  8. O

    Gehl CB400 Chopper KS600 Knife Sharpener Manual Needed

    Hello- I bought a Gehl CB400 chopper. It has the KS600 electric knife grinder on it. Does anyone have a PDF operators manual for the KS600 knife grinder? I want to make sure I set it up right to sharpen the knives before chopping corn this weekend. Thanks in advance! -Jesse
  9. O

    Ford equipment question....

    Cobey made them for Big Blue. Harsco Corporation owned Cobey and Big Blue. Big Blue were identical to Cobey's line of equipment, just painted blue/white. Cobey was red/white. I only know this after doing some research recently (and picking up some original operators manuals), as I picked up...
  10. O

    Gehl Forage Harvester value

    Hello- My neighbor is selling an old Gehl FH84 chop-all field harvester with single row corn head. Other than tightening some chains, the machine looks in pretty good shape. Belt that runs the flywheel looks brand new. Located in central Wisconsin. Looking for a value to start at hir...
  11. O

    M&W hand clutch for Farmall M

    I am pretty sure the tractor has been scrapped. It is no longer in the yard.
  12. O

    Chattanooga Cultipacker Color

    I have one, and i can still see the red color on parts of it. So, red was original
  13. O

    International 56 two row planter fertilizer auger

    Hello- To answer a few of the questions, the planter is set up for 36" rows. The auger fits just fine in the fertilizer box and cast iron discharge pieces on each end of the fertilizer box. My only concern was that the auger is too short at 33". Center to center on the drop tube openings on...
  14. O

    International 56 two row planter fertilizer auger

    Hello- I am helping my neighbor get an International 56 two row planter that he bought last fall. I believe this is an early 56 planter. Has steel fertilizer tub and the side markers have shoes, not discs. It has double disc openers for the seed and fertilizer. My question is that I am...
  15. O

    Gehl 135 hammer mill screen dimensions

    Hello- Can anyone verify the correct thickness of the screens for a Gehl 135 Mix-All hammer mill feed grinder? These screens are for the 21"wide hammer mills that Gehl made. They fit many different Gehl hammer mill models as Gehl used the same screens. My part number for the 3/4" screen...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top