(800) 853-2651
SHOP NOW

Recent content by Owarzecha

Yesterday's Tractor Forums
  1. O

    New holland super hayliner 68 pickup times don’t engage

    Sprayed some wd-40 in the oiler holes and around the pin and will let it sit overnight.
  2. O

    New holland super hayliner 68 pickup times don’t engage

    On closer inspection the two pins on the drive shaft are not popping out to engage the hay rake, what causes the pins to pop out?
  3. O

    New holland super hayliner 68 pickup times don’t engage

    Video
  4. O

    New holland super hayliner 68 pickup times don’t engage

    Help! Need to bale tomorrow and my bailer pickup tines aren’t engaging. The flywheel that is supposed to to engage with the drive wheel isn’t sitting right against it and feel rather loose, I thought maybe the chain is suppose to engage when the front of the rake bar is down but while it touches...
  5. O

    Case312 hydrolic fill

    Perfect and thank you very much!
  6. O

    Case312 hydrolic fill

    Need some help, I know the big nut with dipstick attached here in picture a is the gear transmission oil. Trying to figure out where to fill up hydronic fluid, is that this in picture b that I am pointing to?
  7. O

    Case 312 wide front end needed

    Where did you see the bushings for sale? I believe that I need a o6472 part number?
  8. O

    Case 312 wide front end needed

    Well I finally got it all off, not the easiest task to say the least. The shaft looks fine but yes I probably need to replace this brass bushing on the inside. Thats going to be a pain to knock out I can tell as well.
  9. O

    Case 312 wide front end needed

    I can take the bracket off to get welded but I am trying to figure out how what I believe your calling the axle pin comes out (see picture) how does this remove to take off front axle?
  10. O

    Case 312 wide front end needed

    Hello, I have a case 312 with the wide front end. Motor runs strong but recently have issue and looking for new front end. Not sure where something like this can be found? Appreciate any help or if someone is looking to buy one of these? I am located in Stacy Mn north of the twin cities...
  11. O

    To20 3 point looses power after heating up

    Safety first for sure and I appreciate that... I will be tearing this apart this evening and will post pictures of the findings. Stay tuned.
  12. O

    To20 3 point looses power after heating up

    How high do I have to block the rear wheels. Is that necessary to reduce the oil level or can I just remove the inspection cover and look without doing that and having hydraulic fluid pour out?
  13. O

    To20 3 point looses power after heating up

    So I will try replacing fluid with new 5 gallons of 90w GL-1. If that doesn't work would next step be pulling the entire pump out ? I assume at that point it might be cheaper to buy a new pump at approximately $300 than overhaul this one as the overhaul kits appear to be about the same price? or...
  14. O

    To20 3 point looses power after heating up

    Hey folks, my TO20 3 point seems to loose power after running up and down for about 5 minutes, it will start by lifting a brush hog up no problem, then each time I let down and pick up it gets slower and slower until it won't lift it off ground more than a couple inches... fluids are full and...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top