(800) 853-2651
SHOP NOW

Recent content by Ozarks Hunter

Yesterday's Tractor Forums
  1. O

    4430 load shaft replacement

    I will definitely clean everything really good before doing any work. Looking it over a little more it seems to only leak when the arms are down. I chained them up overnite and no leaks. I may continue working out this summer and work on it this winter.
  2. O

    4430 load shaft replacement

    I am preparing to replace the load shaft, bushings and seals on my 4430. Part of the process is to ensure the load control lever is all the way down before removing the old one. The lever has been stuck and will not move since I've owned the tractor. I have taken the linkage off and it will not...
  3. O

    188d troubles

    I looked back through my emails and the gasket and fire rings I bought were almost $500. The crazy thing is the head gasket in the picture I posted is the exact same as the gasket I removed when I took it apart the first time. I don't know how but I do know it ran fine for over 20 years. It did...
  4. O

    188d troubles

    Was not at operating temp when checked. Not sure on the head. Didn't look into it much when the head came back. Possibly wrong sleeves is interesting. When I get home I'm a couple months I'll tear into it and hopefully figure it out.
  5. O

    188d troubles

    It was way more than that. Here is a number on the block below the starter. I will definitely go with you whatever I do with it. Leaving this weekend for a few months so it will be a bit before I get back to it.
  6. O

    188d troubles

    Engine could have been changed I guess as I don't know anything about the tractor before my grandpa had it. I wouldn't even mess with it if it wasn't his old tractor. Here is a picture I found in my phone that I probably had sent to Dale. I assume it's showing the old gasket or the replacement...
  7. O

    188d troubles

    I know the hard plastic seals you speak of. I kinda wondered how the carbon dam could seal compression especially when the injector has been pulled several times. I have a 450 case dozer with the same engine and the hard plastic is on it. The reason for the rubber on the engine in question is...
  8. O

    188d troubles

  9. O

    188d troubles

    Hmmm. I was having injectors tested at a diesel pump shop and asked about sealing compression and was told that the rubber between the injector and the head was not to seal compression. They said the white bulge area on the injector that fits inside the head was the seal. Sounds like that was...
  10. O

    188d troubles

    I did get the separate fire rings but as far as correct ones I guess I'm not sure. The gasket came from Dale Weiss who as I understand is a very knowledgeable man when it comes to case stuff so I would think he sent the right ones.
  11. O

    188d troubles

    Looks like it's a 68.
  12. O

    188d troubles

    Been so long since I looked up the serial number can't remember the year. I know it has the narrow flange sleeves.
  13. O

    188d troubles

    I had to put a little thicker rubber washer between the injector and head. That would hold the injector up just a bit in the chamber. Would that cause a problem?
  14. O

    188d troubles

    Pencils. I'm going to just order a set. They're pretty cheap.
  15. O

    188d troubles

    Have thought about that as well. Nice tractor in your picture. This engine is in a 430.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top