(800) 853-2651
SHOP NOW

Recent content by Paint Horse

Yesterday's Tractor Forums
  1. P

    Massey 65 starting issue

    Yes, that's tonight's plan. Thanks
  2. P

    Massey 65 starting issue

    I have a 65 with the Continental G176 gas engine. Switched to electoral ignition over two years ago. Have had no issues, starting, running, nothing. Till 2 weeks ago, while moving round bales, it started running rough, like a slight misfire. Then it died. Couldn't get it to kick over...
  3. P

    Ignition problems

    Good points. I'll get him on this forum and he can explain what's he's done. Thanks
  4. P

    Ignition problems

    Ok, we'll take a look. Thanks
  5. P

    Ignition problems

    Here I go again...I will repeat myself and tell you that I have very limited knowledge of mechanics and engines, but I've got a 58 MF65 gas that's got a generator, and has been covered to an electronic ignition. We have replacedall the wires on the ignition side of this tractor...
  6. P

    Safety switch..

    That makes sense, I'll try that, thanks. Appreciate the response
  7. P

    Safety switch..

    Thanks, I'll give that a shot as well. Appreciate it.
  8. P

    Safety switch..

    Thanks. Appreciate the info !
  9. P

    Safety switch..

    Thanks for the pics , and yes Sir, I tend to be a death magnet, so I'm always making sure I'm aware of tractor safety issues.
  10. P

    Safety switch..

    Ok guys, I'm very limited on tractor knowledge, but with reading these forums , I'm learning more and more, thanks for that. I've got a 1958 mf65 gas, converted to electronic ignition and alternator. I believed I'm having problems with the neutral safety switch, as sometimes when ignition...
  11. P

    Hydraulic fittings

    Thanks, totally agree. These weren't cheap, no sense in getting chips in those ports.
  12. P

    Hydraulic fittings

    Thanks, I'll check again. Appears straight as I look at it, but could have a slight taper. Problem is, limited stores around here carry couplers, and my current cylinder has a split wiper, and deep scratch in the rod, and is dripping fluid like a river , and need to get it changed tomorrow.
  13. P

    Hydraulic fittings

    Manufacturer states 1/2 NPT. Just tightened by hand , no wrench, about 3 turns before hitting that resistance. I'm going to try a different coupler just to check.
  14. P

    Hydraulic fittings

    Yes, I checked with manufacturer before purchasing the 90 fittings. They said their ports are 1/2 NPT. Guess I'll do another check with a different coupler.
  15. P

    Hydraulic fittings

    Just turning by hand, no wrench, I encountered resistence after about 3 full turns.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top