(800) 853-2651
SHOP NOW

Recent content by Paul for Wi

Yesterday's Tractor Forums
  1. P

    Pics From June 13th Jasper,MO Pull

    Thanks for posting, good to see folks out there pulling.
  2. P

    2096 3pt stuck in position

    After not finding any problems in the linkages that operate the 3pt. I hooked the tractor to a disk (ram ) and it would try to pick it up just slightly and the action was very slow- so I am thinking the problem is with the main hyd. system. The power steering seems to work normal for what its...
  3. P

    2096 3pt stuck in position

    Thank you both for the suggestions, hopefully I will have some time now that most of the planting is done to look into the problem and let you know how I make out.
  4. P

    2096 3pt stuck in position

    Was using the 2096 with a heavy mounted 3pt load (Dyna-Drive) last week and when I went to lift it at the end of the field it started to come up and then just kind of dropped down- but did not drop all the way to release the pressure from the pins, I had to lift up the implement to unhook it...
  5. P

    Biggest Horse in Town

    While the JD had more draw bar horse, the 990 had a maximum low gear pull of 12,629# vs. the 820 at 8667#. The 990 had 84.10 hp on the belt vs. the 820 at 72.82
  6. P

    60's Ind. JD Model #?

    This tractor was built in Dubuque, Model # T4W1D serial 0588637T this tactor is a 3 cylinder gas loader tractor with backhoe. What would you call it when ordering parts ( is there a farm model that's the same? ) It has the heave cast 1st gen. front end piece. Thanks
  7. P

    Oliver 1850 weight

    Will a 1850 diesel with wide front and pressed steel rears otherwise stock make 8500#?
  8. P

    planting spuds

    Do you use Chloropicrin fumigant?
  9. P

    What Oliver would this be?

    Thats what I was thinking, one generation twice removed.
  10. P

    What Oliver would this be?

    http://appleton.craigslist.org/grd/4478245615.html
  11. P

    Managed to get started haying today

    I am guessing its a 2755...
  12. P

    Lots of money working in this field today

    They are hilling potatoes. Here we don't hill until the potatoes are ready to come out of the ground-usually 2-3 weeks after planting.
  13. P

    2096 powershift/clutch

    Thanks for the reply, I will call when I have some more time next week. The filters and hy-tran are new. Also replaced the plastic screen on the other side because there was a small hole in it. Did not seem like a lot of shavings or trash in the oil to me.
  14. P

    2096 powershift/clutch

    2096 has a problem that comes and goes. If it takes off after start up, every thing operates fine the whole time it is running. Once in a while, after start up the cluth/power shift pump won't surge and pressure up and nothing happens-it will not move, shut it off and sometimes it will work...
  15. P

    How to ID 88 engine

    Thanks for the reply, the tractor sold to fast for me.
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top