(800) 853-2651
SHOP NOW

Recent content by PCH

Yesterday's Tractor Forums
  1. G

    Pump Support Pin T035

    Hey Fellas - my pump support pin is leaking and I need to re-gasket it. If I remove it to do so, do bad things happen inside the trans? Thanks!
  2. J

    silent drive chain connecting link?

    the chain is for a snowmobile I need to shorten it,is there a special link or is it just the pin you put in? thanks for any help
  3. P

    jubilee parts manual

    I was looking for a parts manual for a 53 naa jubilee.fond 2 different manuals, 1 is for 9n2n8n and naa 39 to 54, and the other is for naa thru 801 53 to 64. which one is better for the jubilee, or does some one know how to get a specific manual for a jubilee. I am tech challenged. didn't...
  4. G

    1948 oliver HG crawler

    Can anyone help me with a starting problem? I recently bought this tractor and it starts and runs great until I stall it under load then it won't start again. It seems like it might be flooding it's self but not sure. I shut off the fuel when this happens but it still takes about 1 to 1 1/2...
  5. P

    putting a 310 into a 770 oliver (flywheel question)

    The 310 is rated at 2640RPM, will the flywheel off the 770 rated at 1750 take being spun at 2600RPMs without a problem. Or do I have to find a steel flywheel? Or could a machine shop turn down the 310 flywheel to 13.25 in diameter to match the 770 flywheel? Any ideas welcome, don"t want the...
  6. P

    narrow front for a massey 102

    thanks for the information
  7. P

    narrow front for a massey 102

    Does anyone know if a narrow front off of any other model massey will fit the 102 sr. Thanks
  8. P

    310 head work

    How big of intake valves can I safely put in a 310 LP head?
  9. P

    310 LP head

    how big of intake valve can I go to ? Will 2 inch work or can I go bigger? Is there an after market rod that will work with a standard bore and stroke? Everyone says that the 310 rod is junk. Thanks
  10. P

    310 oliver engine

    Is there any automotive engine rods that will work with an offset grind of crank? Or would it be better to have them built?
  11. P

    Question for Semper Fi 88 Darton sleeves

    Thanks for the help
  12. P

    226 continental

    Anybody know the best place to find parts and information on building a pulling engine? Thanks
  13. P

    226 continental

    Anybody know the best place to find parts and information on building a pulling engine? Thanks
  14. P

    Question for Semper Fi 88 Darton sleeves

    Hello you had posted that Darton makes a sleeve that would drop into factory 310 block, increasing bore size to 4.060. Where do I find these sleeves? With these sleeves do you know what the deck height is? Thanks
  15. P

    coupling up a 310 oliver in a different tractor

    What is the best way to hook up the engine to transmission.Putting a 310 in a oliver 770,not using the T/A.The original shaft too long, any ideas?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top