(800) 853-2651
SHOP NOW

Recent content by phil fenner

Yesterday's Tractor Forums
  1. R

    Farmall m clutch

    I got a old Farmall m tractor running and the clutch adjustment is all the way out at the end of its threads but the clutch does not engage unless pressed clear to the end with a lot of pressure, is there an easy way to adjust this or am I gonna have to go inside and operate I don't know how...
  2. D

    Massey Harris Pony info needed

    A fellow near me has two pony's for sale. One complete the other had a tree fall on it! They have not run in a long time. They have the Continental flat head 4 cylinder engines. I see by the serial number listing on this site that there is one group from 47 to 49 that start with PGS and from 50...
  3. T

    Kubota B7100 Hydraulic pump rebuild

    I was getting Hydraulic fluid in my engine oil and after a little research it looked like the only place this could happen was in the hydraulic pump. I bought the seals and o-rings, pulled the pump but now I don't see any obvious way to remove the outer bushings. Can anyone tell me how to...
  4. D

    JD 1020 3pt issue

    I am trying to troubleshoot the 3 point problem on a 1020 diesel.The problem is that when soon as the tractor starts up the 3pt goes up by its self regardless of lever position. then it will not go down the filter has been removed and was cleaned no findings there. Where should i go to check next?
  5. rrlund

    Cow/calf guys where it's been cold

    Any of you guys up here where it's been so miserable cold all winter,I have a question if you're calving yet. Do your calves seem to be larger than normal? After last springs disaster,I didn't breed to start until late April. I had a guy tell me the other day though,that the calves might be...
  6. C

    Massey Ferguson lawn tractor with Onan Engine

    Would anyone know which models of Massey Ferguson used an Onan P or B series engine?
  7. J

    OT parts washer tank

    My parts washer tank developed a leak, I repaired it once, and its time for a replacement. Where can you buy a tank without the pump. What is the best material for a solvent parts tank? I thought about using the bottom part of a barrel, but a good cover is needed to prevent evaporation. I...
  8. H

    Tranny Fluid Change

    4 gals kerosene, 2 qts ATF, couple containers cheap rubbing alcohol, a few low speed laps around driveway, pull plugs....what a pretty pink 'milky' mess, look in filler hole. YEAAA!!! So much cleaner in there. HOWEVER, now I know where allllll the gaskets needing replacement are ~eye roll~ Both...
  9. M

    B6200 Kubota oil leak

    My Kubota B6200 has oil coming out of blow by tube. It has no blowby at all. It does this after running it for about one hour. Tractor has strong compression. I also noticed the hydraulic oil dipstick level goes down. Kubota dealer said an o ring from around hydraulic pump could be worn and...
  10. M

    Tractor Pull

    The antiques are 1st gear only, expect 30-40 tractors per class! Bring a empty stomach, and some extra horsepower, it is a short chain!
  11. A

    Case IH 885 Fuel Vacuum Problems

    I have an '89 Case 885 cab tractor with dual fuel tanks. This weekend I was traveling from one field to the next and it started to die just if it was running out of fuel. I crutched it along to the field and it died. I checked and had 2 full tanks of fuel. When I checked the filters they were...
  12. A

    MW Injection pumps

    What is the std injection pump timing on these 466s equipped with these pumps. Does that mw pump have a timing advance built into them?? I am sitting at 28 degrees on the flywheel. And seems to run fine but looking for more info. Thanks
  13. G

    attention Bruce (VA)

    I understand you have a few of the steele balls for the 8n quadrant plate, would you be willing to part with one? I will pay you.
  14. I

    Federal Tractor?

    I need help. Found this tractor(?)adapted into a cotton stripper. Has a flat head 6 cylinder engine. My uneducated guess is that the engine and running gear have been put on a "shop built" tractor-cotton stripper. I have numerous pictures available if anyone can help me out. Email me if you...
  15. B

    SC starter ring-gear replacement

    The "55 SC starter always engaged very hard. Now the teeth of the ring gear show the effects. First question: why does the starter slam in so hard? Second question: Having never replaced a ring gear, what book or manual will show me exactly how to proceed with the removal and replacement?
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top