(800) 853-2651
SHOP NOW

Recent content by phil51

Yesterday's Tractor Forums
  1. P

    Super H Starting Issues

    Super H, has always started real easy, never really needed any choke or anything. Until recently, now itll crank until it floods. Itll only start after a shot of either (which I hate to do) or if its pull started. Any suggestions as to what may be the problem all the sudden? Thanks
  2. P

    Super H Dead Battery

    Thanks guys for the help. Ill start with a new battery and go from there.
  3. P

    Super H Dead Battery

    Read 1.7 on the volt meter. Ive pull started dead tractors many times, so just wondering if theres something else wrong. But I was wanting to completely rule out battery before I moved on to checking other things.
  4. P

    Super H Dead Battery

    Super H 6 volt system. Is it possible for the battery to be so dead it would cause the tractor to not start when trying to pull start it?
  5. P

    MW 9 Speed Vs TA

    Are the high and low ranges in each gear on an M with a 9 speed the same as a 400/450 using both sides of the TA?
  6. P

    Farmall M PTO

    I am going to be replacing the PTO shaft in my M. Do I need to remove the rear end oil before I take the PTO cover off to remove the shaft? Thanks
  7. P

    Zenith Carburetor gasket kit

    Treadwell Carb in NY is where I get my Zenith parts.
  8. P

    Cockshutt 40

    A 262 will get you 80-85 hp. Plenty of power for any 3 mph top cut class or deadweight.
  9. P

    Cockshutt 40

    If you can find a 262 buda to drop in it would be easy horsepower.
  10. P

    47 m puller

    There?s not exactly a ?cheap? way to do it. If you don?t have anything currently invested in your motor I?d recommend getting a 264 or 281 block, get it tested and bore it out to 4 3/8?. Add a 450 lp head, and have some cam and carb work done. That should get you around 80 hp. Anything more...
  11. P

    Design Suggestions on Building Dead Weight Sled

    Off the top of my head based on what I pull on, typically the sled for dirt is about the width of whatever size concrete blocks you?re using, roughly 6? for us, and around 10? long. Weld about a 6-8? strip on either side where the hooks will be pointing at a 45 upward, and a 3? or so strip on...
  12. P

    M Governor Adjustment

    I just got done rebuilding an M and need to adjust the RPMs. When I give the tractor full throttle, the RPMs are higher than they should be. Can someone please explain how to adjust my governor so the RPMs when I give it full throttle are less? Is there a governor diagram somewhere that shows...
  13. P

    Tire plys

    Personally I?d prefer the 8 but I agree with mmfan that figuring out the correct tire pressure is key. I would not recommend buying the tires if they are new though, you?d have better luck with an old hard set of tires.
  14. P

    E4 Shifting Pattern Decal

    Does anyone know where I can purchase a shifting pattern decal for an E4? I can?t seem to find them anywhere. Thanks
  15. P

    Farmall M starter options

    You can get a gear reduction starter from Lemmons
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top