(800) 853-2651
SHOP NOW

Recent content by pkjunior

Yesterday's Tractor Forums
  1. D

    1996 F250 Codes issue

    A while back I posted about the F250 I bought for my son. It was running extremely rich (blowing black smoke, carboned up spark plugs) but the engine codes were showing that it was running lean. I couldn't figure it out and I brought it to one shop that I had been having pretty good luck with...
  2. 6

    About pivot pin for ford 3000

    Hey , I'm not having luck with getting the correct pivot pin for my 1966 ford 3000 tractor, I removed the solid pin to replace with a hollow to run my 730 loader, the first pin I received was incorrect completely by the vender , the 2nd one which replaces part number c5nn3127b is too short...
  3. D

    430 2 cylinder hoods

    Can someone tell me the difference in the hoods on a 430 with or with power steering? I see two different part numbers, but would like to know what the physical difference is. Thanks, Mark
  4. N

    Questions on buying loader control valve for tractor

    I need to buy a loader control valve for my tractor and have a couple questions. 1. I think my crankshaft run pump puts out 17gpm. I assume I need to get a valve that produces at least 17gpm to get the full benefit of my pump? For example, doing a quick search I'm looking at a 12gpm and a...
  5. M

    8N serial number

    Curious if someone could help me decipher this serial #. I just picked this 8N up from an estate and want to learn about its history.
  6. J

    Nason paint code JD Green

    Thinking of using Nason urethane single stage on a JD 830 2 Cyl. I've looked through the posts and found a few codes for JD green but they don't come up at my local dealer. Does anyone have a code? I'm thinking of the ag green, but maybe the classic would work as well. Thanks
  7. M

    SCV Barrel Orings

    So in this nifty oring kit JD makes it says to use the orings and backup rings for tractors pre 1970 and the rubber seal/ring/thingy post 70. Wondering if one is better than the other or if the casting is machined different as they both fit the same. Also what are the extra square orings for...
  8. E

    cover for my 1952 ford 8N

    I use a tarp drapped over the engine, transmission, and differential. Tied at each corner of the front axle, tied underneath the tractor side to side, and tied at each corner of the rear axle assembly. I use heavy rubber ties Would llke to look into a more form fitted cover that fits over...
  9. B

    1086 540 PTO shaft

    Nephews had the 540 shaft twist off yesterday. Dealer wants around $1500 to fix it. Wondered if anyone has been into replacing a shaft before. Can it be done by removing the PTO unit from the rear or does the platform have to come off? I've got ideas I might get involved in this thing yet...
  10. R

    Overbrook Kansas Tractor Pull A Go!!!!!

    We missed all the rain today and the weather looks great for Saturday! It's dry enough for good parking!! Hope to see you all saturday! Any questions give me a shout! 7853932501 <image src="http://forums.yesterdaystractors.com/photos/mvphoto22868.jpg"/>
  11. 5

    massey 44,leak

    have a leak on a 44 Massey,on the transmission cover that is square,but with points up and down with four half inch bolts holding it on,when I remove it,is there something it holds in place ? it is in the belly on the right side of input shaft.Thanks
  12. A

    My 60 update

    My 60 wouldn't fire up since about 1 1/2 yr. ago. I've been in here asking for suggestions as far as what steps I should take in troubleshooting. I have put in new 3116 plugs set at .030", points look good & set properly, put in new condenser, new rotor button, new distributor cap, new (dealer...
  13. S

    HVAC Installation

    I'm going to be helping a neighbor install a replacement Goodman 3 ton heat pump system this Saturday. The evaporator coil is aluminum. It has a copper spin closed cap brazed/soldered/? to the stub where the refrigerant return line will attach. I've never tried to braze to something like...
  14. jon f mn

    gosh darn dang nammit tires round 7

    Nuther puncture today, same tire. Wonder what the world record for punctures is in a tire. Was lucky today in that I stopped at a rest area and heard it leaking, it was down to 30 lbs and would likely have blown soon. I will probly change this tire out, but wouldn't want to pay to have a tire...
  15. A

    F20 serial number

    Bought the remains of a F20 from the local scrapyard yesterday. Serial number on the frame reads 137313. That's a real late one. It has the factory cast rear rims, foot brakes, and a real nice pto extension. Pleased to find these items. To bad the rest of the tractor was gone. Should help me...
See more
Yesterday's Tractor Forums
Buy Tractor Parts Here Buy Tractor Manuals Here

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2025 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top